Rules For Safe Driving; Assistance Service - Peg-Perego John Deere GATOR HPX IGOD0060 Use And Care Manual

RULES FOR SAFE DRIVING

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• If the vehicle is overloaded on steep slopes, the
overload cut-out will immediately disconnect the
power. If this happens,
REMOVE THE FOOT FROM THE
. The electrical brake will be
ACCELERATOR
activated, slowing down the descent of the vehicle.
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

ASSISTANCE SERVICE

offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted. See
the page on spare parts to find out how to identify the
serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
1 • Insert the two windshield tabs into the openings
on the hood. Turn the windshield in the
direction shown by the arrow.
2 • Fasten the windshield using the two screws
provided with the vehicle.
3 • Join the two steering wheel parts.
4 • Place the horn in the steering wheel's central
hole, following the instructions in its packaging.
5 • Apply sticker No. 10. Mount steering wheel on
its bar as shown in the picture.
6 • Fix the steering wheel using the screw and bolt
supplied; make sure to fit the screw in the
circular hole and the bolt in the hexagonal hole.
7 • Plug toy-key into its slot located on car bonnet.
8 • Apply sticker no. 3. Fit the bumper by inserting
the lower tabs in the two slots in the bodywork,
then clipping on the two upper sleeves.
9 • Fix bumper using the two screws supplied.
10 • Mount fuel cap on its base.
11 • Fit the previously mounted piece in its slot on
car body; orientate it as shown in the picture.
12 • Rotate it by 90 degrees until automatic blockage
is reached.
13 • Split handles - using scissors, if necessary - and
remove the two connecting plastic pieces.
14 • Unscrew the two screws you find on the caisson
(see picture). Remove plastic bush. Keep these
screws: you will use them later to fix handles.
15 • Snap handles into place as shown in the picture.
16 • Fix them with the two screws previously
removed.
17 • Split mudguards - use scissors, if necessary- and
remove connecting plastic pieces.
18 • Snap mudguards into place on the caisson.
WARNING: mudguards must be mounted
according to letters printed inside of them: 'L'
stands for 'left' and 'R' stands for 'right'.
19 • Split arrows - use scissors, if necessary- and
remove the connecting plastic piece.
20 • Fit arrows in their slots on the mudguards; put in
the external side first (B). Press down on the
inner side (A) to automatically lock arrows.
21 • Adjust caisson aligning its holes (see details
shown in the picture).
22 • Fix caisson to car rear with the two pins
supplied until blockage is reached, as shown in
the picture.
23 • Right pin correct position.
24 • Join the spring and red latch as illustred. Lift
piston and fit red hook in its upper side as
shown in the picture.
25 • Keep piston lifted and align its hole to the rear
hole on the caisson (see picture).
26 • Fix it with the pin shown in the picture.
27 • Make sure that the pin is correctly mounted as
shown in the picture. Push the caisson down.
28 • Mount handles on the two sides of the double
seat.
29 • Fix each handle with the three screws supplied.
30 • Align double seat to holes according to the
child's height; fix it from underneath with the
four knobs supplied. Gator has 4 positions (see
scheme). WARNING! Slide the caisson
backwards to adjust seat on position 4. See
pictures 40-46.
31 • Unscrew safety screw on battery housing.
32 • Unfasten side flaps pulling them outwards.
33 • Push the front block down.
34 • Connect system plug to battery plug. The vehicle
is ready for use.
FEATURES AND USE OF THE VEHICLE
35 • A: HORN. Press the yellow part in the centre to
sound the horn.
B: TOY KEY. This key does not turn your vehicle
on; it is a toy-key.
C: HANDLE. Passengers can use this handle for
additional safety when the vehicle is turned on.
36 • DRINKS HOLDER - Gator has two drink
holders for cans or bottles on each of the two
front fenders.
37 • ELECTRIC ACCELERATOR/BRAKE PEDAL.
CONSUMER
Brake activates automatically moving your foot
away from the pedal.
38 • The caisson is provided with a panel that can be
opened by pushing the two red side levers
ASSEMBLY
upwards.
39 • The tip-up caisson can carry objects for a
maximum of 10 Kg. To tip the caisson over, push
rod upwards and unlock it as shown in the
picture, lifting the caisson using side handles.
40 • Remove the three fixing pins to slide the caisson
backwards by one position; unlock them by
pulling flaps downwards. Use a proper tool if
necessary. Remove the caisson.
41 • Break connecting parts to remove oval pivots
from their joints.
42 • Insert joints in their housings on the bottom of
the vehicle.
43 • Fix them using the previously removed pins.
44 • Re-place the caisson on the vehicle.
45 • Align rear holes on the caisson to those of the
joints. Fix the caisson with the two oval pivots
previously removed from their joints.
46 • Fit piston in the first front hole of the caisson
using the last available pivot. Always make sure
that pivots are properly fixed. Push the caisson
down.
47 • GEAR LEVER. Gear has three speeds. Push gear
lever downwards to activate rear gear; push it
upwards to activate second gear. WARNING!
Only first and rear gear work when the vehicle
has just been taken out from its package. See
steps 48 and 49 to activate second gear.
48 • Unscrew safety screw to unlock second gear
block.
49 • Fit second gear block in the second hole as
shown in the picture. Now you can use the
second gear, too. If you do not want your child
to use second gear, fit second gear block in the
first hole.
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
50 • Open battery housing following steps 31-33.
Remove battery lock.
• Disconnect plugs.
51 • Remove battery and replace it.
52 • Reconnect plugs. Mount battery lock and close
battery lid.
53 • WARNING! Make sure battery lid is always
properly fixed with its screw.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
54 • Disconnect plug A (electrical system) and plug B
(battery).
55 • Connect battery charger to a domestic socket
according to instructions provided. Connect plug
B to plug C (battery charger).
56 • When the battery is ready, disconnect battery
charger from the domestic socket; disconnect
plug C and plug B. Properly fit plug B in plug A.
Always make sure battery lid is properly closed
and fixed.