Setup; Connections; Rf Output Channel; Hint For Cable Box Or Satellite Box - Magnavox MWD2206A Owner's Manual

Connections

Please refer to "Basic TV Connection" on the front page before you use this unit.

RF Output Channel

If channel 3 has been already occupied
for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
) Press [SOURCE] on the unit so that the
VCR OUTPUT light is lit.
• If noise appears on the TV screen, press
[VCR/TV] on the remote control.
4) Press [PLAY B] once.

Hint for Cable Box or Satellite Box

(Cable box or
Satellite box)
Satellite or
IN
OU T
Cable TV
signal
Select this connection when you want to view or record a
scrambled channel. With this connection, channels cannot be
changed on the unit. You can view or record ONLY
the channels you have selected on the cable box or the
satellite box.
• While you are recording, only the recorded channel can be viewed.

Connection to an Audio System

Method 1
Stereo system
Audio
Audio cable
(supplied)
AUDIO OUT
(Analog)
DVD/VCR
DIGITAL
AUDIO OUT
(DVD mode only)
Hint
• Playing a DVD using incorrect settings may generate noise distortion and may
also damage the speaker.
5) After a few seconds, press and hold
[PLAY B] on the unit for  seconds.
• The RF output channel will change to
channel 4 from channel  and you will
see a playback picture.
• When a picture does not appear on the
TV screen, repeat step 4.
6) Press [STOP C] to stop playback.
(Back of DVD/VCR)
ANT-IN
RF cable
ANT-OUT
(supplied)
(Back of TV)
Analog audio
L R
input jacks
DVD/VCR VCR
AUDIO OUT
L
R
or
DVD
COMPONENT
AUDIO S-VIDEO
VIDEO OUT
OUT OUT
L
R

Setup

To select channels of the cable box or satellite box
1) Turn on the unit by pressing [STANDBY-ON], then press
[VCR/TV]. The POWER ON indicator on the front panel
will light, then press [SKIP/CH. G / K , H / L ] to select
channel  or 4 (the same channel as the output channel of
the cable box or satellite box).
• If you use the channel 4, you need to change the unit's
RF output to channel 4. Refer to "RF Output Channel".
2) At the TV, select channel  or 4 (the same channel as you
have selected at step 1).
) On the cable box or satellite box, select the channel you
want to view or record.
Dolby Digital decoder,
MD deck or DAT deck
Audio Coaxial
Digital cable
(commercially
available)
DIGITAL
AUDIO OUT
Connection
Connecting to a Dolby Digital decod-
er for Dolby Digital audio output.
Connecting to the other equipment
(an MD deck or DAT deck etc.) with-
out Dolby Digital decoder.
* To complete these settings, refer to pages 20-21.
Hint
• The audio source on a disc in a Dolby Digital 5.1 channel surround format can-
not be recorded as digital sound by an MD or DAT deck.
• By hooking this unit up to a 5.1 channel Dolby Digital decoder, you can enjoy
high-quality Dolby Digital 5.1 channel surround sound as heard in the movie
theaters.
• Playing a DVD using incorrect settings may generate noise distortion and may
also damage the speakers.
– 6 –
Hint
• The RF output channel does not
change when you adjust tracking
during playback. In this case, stop the
playback, and start the playback again.
After that, press and hold [PLAY B]
on the unit for  seconds again.
Method 2
Digital audio
COAXIAL
input jack
DVD
DIGITAL
AUDIO S-VIDEO COMPONENT
VIDEO OUT
AUDIO OUT OUT OUT
COAXIAL
SETUP > QUICK>
Setting
DOLBY DIGITAL
BITSTREAM
PCM
EN