Setup; Connections; Rf Output Channel; Hint For Cable Box Or Satellite Box - Magnavox RSMWD2205 Owner's Manual

Connections

Please refer to "Basic TV Connection" on the front page before you use this unit.

RF Output Channel

If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Hit [SOURCE] on the unit so that the VCR
OUTPUT light is lit.
• If noise appears on the TV screen, hit
[VCR/TV] on the remote control.
4) Hit [PLAY B B ] once.

Hint for Cable Box or Satellite Box

(Cable box or
Satellite or
Satellite box)
Cable TV
IN
OU T
signal
Select this connection when you want to view or record a scram-
bled channel. With this connection, channels cannot be changed
on the unit. You can view or record ONLY the channels you have
selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be
viewed.

Connection to an Audio System

Method 1
Stereo system
AUDIO
Audio cable
(supplied)
(Analog)
AUDIO OUT
DVD/VCR
DIGITAL
AUDIO OUT
(DVD mode only)
Connection
Connecting to Stereo System.
* To complete these settings, refer to pages 20-21.
Hint
Hint
• Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
5) After a few seconds, hit [PLAY B B ] on the
unit for 3 seconds.
• The RF output channel will change to chan-
nel 4 from channel 3 and you will see a play-
back picture.
• When a picture does not appear on the
TV screen, repeat step 4).
6) Hit [STOP C C ] to stop playback.
(Back of DVD/VCR)
ANT-IN
ANT-OUT E
RF cable
(supplied)
(Back of TV)
Analog audio
L R
input jacks
DVD/VCR VCR
AUDIO OUT
L
R
or
DVD
COMPONENT
AUDIO S-VIDEO
VIDEO OUT
OUT OUT
L
R
SETUP > AUDIO menu >
Setting
DOLBY DIGITAL
PCM

Setup

To select channels of the cable box or satellite box
1) Turn on the unit by hitting [STANDBY-ON], then hit
[VCR/TV].The "STANDBY-ON" and "VCR" lights on the front
panel will appear, then pressing [SKIP/CH. i
select channel 3 or 4 (the same channel as the output channel
of the cable box or satellite box).
• If you use the channel 4, you need to change the unit's RF
output to channel 4. Refer to "RF Output Channel".
2) At the TV, select channel 3 or 4 (the same channel as you
have selected at step 1).
3) On the cable box or satellite box, select the channel you want
to view or record.
Dolby Digital decoder,
MD deck or DAT deck
Audio Coaxial
Digital cable
(commercially
available)
DIGITAL
AUDIO OUT
Connection
Connecting to a Dolby Digital decoder
for Dolby Digital audio output.
Connecting to the other equipment (an MD deck
or DAT deck etc.) without Dolby Digital decoder.
* To complete these settings, refer to pages 20-21.
Hint
Hint
• The audio source on a disc in a Dolby Digital 5.1 channel surround
format cannot be recorded as digital sound by an MD or DAT deck.
• By hooking this unit up to a Multi-channel Dolby Digital
decoder, you can enjoy high-quality Dolby Digital 5.1
channel surround sound as heard in the movie theaters.
• Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
– 6 –
Hint
Hint
• The RF output channel may
not change when you adjust
tracking during playback. In this
case, stop the playback, and
start the playback again. After
that, hit [PLAY B B ] on the unit
for 3 seconds again.
i /K K j
Method 2
Digital audio
COAXIAL
input jack
DVD
DIGITAL COMPONENT
AUDIO S-VIDEO
VIDEO OUT
AUDIO OUT OUT OUT
COAXIAL
Setting SETUP > AUDIO menu >
DOLBY DIGITAL
BITSTREAM
j /L L ] to
PCM
EN