Table of Contents
Advertisement
Quick Use Guide
1
Connections
Please refer to "Basic TV Connection" on the front page
before you use this unit.
RF Output Channel
If channel 3 has been already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
) Press [SOURCE] on the unit so that the VCR OUTPUT
light is lit.
• If noise appears on the TV screen, press [VCR/TV] on the
remote control.
4) Press [PLAY B] once.
5) After a few seconds, press and hold [PLAY B] on the
unit for seconds.
• The RF output channel will change to channel 4 from
channel and you will see a playback picture.
• When a picture does not appear on the TV screen,
repeat step 4.
6) Press [STOP C] to stop playback.
1
2
Installing the Batteries for the Remote
Control
1
2
1
2
3
2
3
VCR/DVD Switching
OPEN/CLOSE
VCR
DVD
DISC IN
CHANNEL
SOURCE
PREV
STOP
3
VCR
DVD
SOURCE
VCR MODE
Press [VCR] on the remote control.(Verify that the VCR OUTPUT
light is lit.)
DVD MODE
Press [DVD] on the remote control.(Verify that the DVD OUTPUT
light is lit.)
Hint
• Pressing only [SOURCE] on the front panel DOES NOT switch the
mode of the remote control. You MUST select the correct mode on
the remote control.
4
Turn On the Unit for the First Time
VCR
1
Turn on the TV and set it to channel .
• If channel has been already occupied for broadcasting,
see "RF Output Channel" section.
2
Select your language in the first time you turn on this unit.
Then press [B] to go to next step.
STANDBY-ON
or
1
2
3
3
OPEN/CLOSE
STANDBY-ON
/EJECT
SPEED
AUDIO
1
2
3
PLAY
PLAY
NEXT
SKIP/CH.
4
5
6
VCR/TV
7
8
9
SLOW
VCR button
0
+10
DISPLAY
VCR
DVD
PAUSE
DVD button
PLAY
STOP
RECORD
MENU
ENTER
DVD OUTPUT
SETUP TOP MENU
RETURN
light
SEARCH
CLEAR/
MODE
ZOOM
MODE
C. RESET
SOURCE button
SUBTITLE
ANGLE
REPEAT
A-B
T-SET
VCR OUTPUT light
LANGUAGE SELECT
B ENGLISH
FRANCAIS
ESPAÑOL
3
Press [
] to start Auto Set Up.
B
Do you connect the cable from the cable box or the satellite box to the unit's
ANT-IN jack?
Yes
Press [MENU] to exit.
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).
• If "AUTO SET UP" appears on the TV screen again, check the cable
connections. Then, press [B] once again.
5
Clock Set Up
VCR
1
Press [MENU] and select "CLOCK SET".
Then press [B] to go to next step.
MENU
• If the clock is not set, the CLOCK SET screen appears when you press
[MENU]. In this case, go to step 2.
2
Select the current month.
Then press [B] to go to next step.
3
Select the current day.
Then press [B] to go to next step.
4
Select the current year.
Then press [B] to go to next step.
5
Select the current hour.
Then press [B] to go to next step.
6
Select the current minute.
Then press [B] to go to next step.
7
Select "AM" or "PM".
8
To exit the CLOCK SET screen
[ON]
– 27 –
AUTO SET UP
YES
NO
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
or
CLOCK SET
MONTH DAY
1 0 / – –
HOUR MINUTE
– – : – –
or
CLOCK SET
MONTH DAY
1 0 / 0 2
HOUR MINUTE
– – : – –
or
CLOCK SET
MONTH DAY
1 0 / 0 2
HOUR MINUTE
– – : – –
or
CLOCK SET
MONTH DAY
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE
or
0 5 : – –
CLOCK SET
MONTH DAY
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE
0 5 : 4 0
or
CLOCK SET
MONTH DAY
1 0 / 0 2 MON 2 0 0 6
or
HOUR MINUTE
0 5 : 4 0
CH 01
[OFF]
YEAR
– – – –
AM/PM
– –
YEAR
– – – –
AM/PM
– –
YEAR
2 0 0 6
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
P M AM
B PM
EN
Hide quick links:
Advertisement
Table of Contents
