Maintenance - DeWalt D51276-XE Instruction Manual

3. Release pusher from behind nails.
4. Push down front latch (J) then pull up to open front door (K).
5. Remove bent nail, using pliers if necessary.
6. If driver blade is in the down position, insert screwdriver or other rod
into nosepiece and push driver blade back in position.
7. Remove rod and close front door.
8. Lift latch to secure door to nosepiece.
9. Reattach air supply.
10. Reinsert nails into magazine (see Loading the Tool).
11. Release pusher.
NOTE: Should nails continue to jam frequently in nosepiece, have tool
serviced by an authorized D WALT service center.
E
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Make sure compressor tanks have been properly drained prior to use.
2. Keep tool as warm as possible prior to use.
3. Make certain all fasteners have been removed from magazine.
4. Lower air pressure to 80 psi (5.5 bar) or less.
5. Reconnect air and load nails into magazine.
6. Turn pressure up to operating level [not to exceed 120 psi (8.3 bar)]
and use tool as
normal.
7. Always drain the compressor tanks at least once a daily.
NOTE: Please refer to Preparing the Tool under Operation if choosing to
use oil.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct sunlight as
excessive heat can deteriorate bumpers, o-rings and other rubber parts
resulting in increased maintenance.
FIG. 8
L
Belt Hook (Fig. 8)
The D WALT nailers include an integrated belt hook (L) and can be rotated
E
to either side of the tool to accommodate left- or right- handed users. It can
also be rotated out of the way when not in use.
If the hook is not desired at all, it can be removed from the tool.
TO REMOVE BELT HOOK
1. Lock off trigger.
2. Disconnect the tool from air supply.
3. Using the appropriate hex wrench, remove the end cap screws from
the end cap (M) of the tool.
4. Remove the belt hook.
5. Replace end cap and gasket. Ensure that the three screws are tight.
6. Replace and tighten air fitting.

MAINTENANCE

WARNING: Lock off trigger, disconnect air line from tool and remove
fasteners from magazine before making adjustments or personal injury
may result.
ACTION Drain compressor tanks and hoses daily.
WHY Prevents accumulation of moisture in compressor and nailer.
HOW Open petcocks or other drain valves on compressor tanks.
Allow any accumulated water to drain from hoses.
ACTION Clean magazine, pusher, and contact trip mechanism.
WHY Permits smooth operation of magazine, reduces wear, and
prevents jams.
HOW Blow clean with compressor air. The use of oils, lubricants
periodically or solvents is not recommended as they tend to
attract debris.
ACTION Before each use, check to insure all screws, nuts and fasteners
are tight and undamaged.
WHY Prevents jams, leaks and premature failure of tool parts.
HOW Tighten loose screws or other fasteners using the appropriate
hex wrench or screwdriver.
NOTE: Please refer to Preparing the Tool under Operation if choosing to use
oil.
Cleaning
WARNING: Blow dirt and dust out of all air vents with dry air at least
once a week. Wear proper ANSI Z87.1 (CAN/CSA Z94.3) eye protection and
proper NIOSH/OSHA/MSHA respiratory protection when performing this.
WARNING: When cleaning, use only a damp cloth on non-metallic parts.
Many household cleaners contain chemicals which could seriously damage
non-metallic parts and o-rings. Also, do not use gasoline, turpentine,
lacquer or paint thinner, dry cleaning fluids or similar products which may
seriously damage non-metallic parts and o-rings. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement) should be
performed by a D WALT factory service center, a D
E
service center or other qualified service personnel. Always use identical
M
replacement parts. Refer to the Troubleshooting Guide at the end of this
section.
Accessories
WARNING: Since accessories, other than those offered by D
not been tested with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only D
recommended accessories should be used with this product.
Daily Maintenance Chart
WALT authorized
E
WALT, have
E
WALT,
E
5
Recommended accessories for use with your tool are available at extra cost
from your local service center. If you need any assistance in locating any
accessory, please contact D WALT Industrial Tool Co., 20 Fletcher Road,
E
Mooroolbark, VIC 3138 Australia or call 1800 654 155 or (NZ)
0800 339258.
Guarantee
Applicable to hand held Power Tools, Lasers and Nailers.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or
E
workmanship for three years from the date of purchase. Please return the
complete unit, transportation prepaid, to any D
any authorised service station.
For warranty repair information, call (AUS) 1800 654 155 or (NZ) 0800
339258.
This warranty does not apply to
• Accessories
• Damage caused where repairs have been made or attempted by
others.
• Damage due to misuse, neglect, wear and tear, alteration or
modification.
This warranty gives you specific legal rights and you may have other rights
under the provisions of the Consumer Guarantee Act 1993 (New Zealand
only), Trade Practices Act 1974 and State Legislation (Australia only).
In addition to the warranty, D WALT tools are covered by our:
E
FREE ONE YEAR SERVICE CONTRACT
D WALT will also maintain the tool for free at any time during the first year
E
of purchase. This includes labour, parts and lubrication required to restore
the product to sound mechanical and/or electrical condition. Normal wear
parts are not covered in this service. Carbon brushes worn more then 50%
will be replaced.
NOTE: Three Year Warranty is not applicable to items deemed as
consumables. Radial arm saws are covered by a one (1) year warranty
only. D WALT Reserves the right to review its warranty policy prior to
E
launch of any new business development products.
30 DAY NO SATISFACTION GUARANTEE
If you are dissatisfied with any D WALT power tool, laser or nailer, for any
E
reason, simply return it to the point of purchase with your sales receipt
within 30 days for a replacement unit or a full refund.
FREE WARNING LABEL REPLACEMENT: If your warning labels become
illegible or are missing, call (AUS) 1800 654 155 or (NZ) 0800 339258 for
a free replacement.
WALT Service Centre, or
E