Related Manuals for DeWalt D51825-XE
Summary of Contents for DeWalt D51825-XE
- Page 1 INSTRUCTION MANUAL D51825-XE (31˚ CLIPPED HEAD) D51850-XE (20˚ FULL ROUND HEAD) FRAMING NAILERS...
- Page 2 CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. RAFTER HOOK DEPTH SETTING TOOL SPECIFICATIONS MAGAZINE D51825-XE Clipped Head D51850-XE Full Round Head CONTACT TRIP Height 14-1/4" (36.4 cm) 14-1/4" (36.4 cm) Width 6-1/2" (16.4 cm) 7-1/8"...
- Page 3 IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY • Use couplings that relieve all pressure from the FIG. G • Use the tool only for its intended use. Do not WALT TOOL, CALL US AT: 1800 654 155 (Aust) or 0800 339258 (NZ). tool when it is disconnected from the power supply.
- Page 4 • Choice of triggering method is important. Check WARNING: ALWAYS use safety glasses. Everyday FIG. M FIG. R FIG. 1 eyeglasses are NOT safety glasses. Also use face or the manual for triggering options. dust mask if cutting operation is dusty. ALWAYS WEAR BUMP ACTION TRIGGER CERTIFIED SAFETY EQUIPMENT: •...
- Page 5 OPERATION the nailer. This is especially important in cold weather because any To operate the tool using the PLACE ACTUATION method: moisture in the air in the tanks will condense in the cold temperature. 1. Depress the contact trip against the work surface. Preparing the Tool (Fig.
- Page 6 Guarantee 1. To drive the nail less deeply, push the adjust button (M) in. Slide the In addition to the warranty, D WALT tools are covered by our: contact trip (E) down. Push the set button (N) to secure contact trip. FREE ONE YEAR SERVICE CONTRACT Applicable to hand held Power Tools, Lasers and Nailers.
- Page 7 TYPICAL NAILS ACCEPTED BY THE D51825 AND D51850 FRAMING NAILERS FRAMING, DECK BUILDING AND STRUCTURAL ROOF DECKING, SHEATHING AND SUBFLOORING Smooth Ring Smooth Screw Smooth Ring Smooth Smooth Shank Shank Shank Shank Shank Shank Shank Shank NAIL HEAD TYPES Full Round - D51850, 20˚ - 22˚ Collation Clipped Head - D51825, 30˚...
- Page 8 TROUBLESHOOTING GUIDE MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D WALT SERVICE CENTER OR CALL 1800 654 155 (Aust) or 0800 339258 (NZ) WARNING: To reduce the risk of serious personal injury, ALWAYS disconnect air from tool before all repairs. Trigger valve housing leaks O-ring or valve stem failure Replace valve using Trigger Valve Kit: Cat.# D510005...
- Page 9 Portable 5.5 HP Gas 8 HP Gas Industrial Handcarry 2 HP Elec. 14 - 16 CFM 23+ CFM 3.2 - 4 CFM 8 - 9 CFM Compressor will be sufficient for tools at all production rates. Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates.
- Page 12 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 Te Apunga Place, Mt Wellington, New Zealand (0800 339258) (DEC08) Part No. N003226 D51825-XE, D51850-XE Copyright © 2008 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...