Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Axminster UE-127DV1
Summary of Contents for Axminster UE-127DV1
-
Page 2: Table Of Contents
Table of Contents General Safety Rules ......................1 Electrical schematic ......................... 2 Before cutting and pump grease ....................3 The Quick Vise and Work Set Up ..................3 Usage of the vise ........................3 Work set up ..........................3 Special Safety Rules for Metal Saw ..................4 Before using the saw ....................... -
Page 3: General Safety Rules
1. General Safety Rules WARNING Read and understand instructions of this manual entirely before operating the machine. Always wear approved safely glasses /face shields when using the machine. Make certain the machine is properly grounded. Before machine in operation, remove tie, ring, watch, other jewelry, and roll your sleeves up to above elbows. -
Page 4: Electrical Schematic
Electrical Schematic - 2 -... -
Page 5: Before Cutting And Pump Grease
2. The Quick Vise and Work Set BEFORE CUTTING Release the lock pin (A) in Fig.1 to free this Usage of the Vise saw. After service, must relock in the pin properly for your safety and carry. Failure to comply with the warning could result in The vise is mounted on the machine base. -
Page 6: Special Safety Rules For Metal Saw
3. Special Safety Rules for Metal aluminum, wood, plastic and so ˙ Make sure the direction of rotation arrow on the blade matches the direction arrow on the saw. The blade teeth should always point WARNING: For your own safety, do not downward at the front of the saw. -
Page 7: Whenever Saw Is Running
To avoid injury from accidental starting, always unplug saw before WARNING: disconnecting the guard, installing or Read the following warning labels found on removing any blade, accessory or the front of the saw. attachment, or making any adjustment. To avoid an electrical shock, make sure your fingers do not touch the metal prongs on the plug when DANGER... -
Page 8: Motor Safety Protection
circuit wire. Always check the connections, the load and the supply circuit whenever DANGER: To avoid electric shock motor doesn’t work well. Check wire size 1. Do not change the power cord and and length with the Wire Size Chart below. plug to another specification not provided by the manufacturer. -
Page 9: Description And Characteristics
6. Description and Characteristics 7. Operating This 127DV1 portable band saw is made Information before Operation as light as 24 kg by weight for your fitness to transport to any worksites. Be sure the blade isn’t in contact with the work This machine frame is cast by the when the motor is started. -
Page 10: Auto Cutting
Auto Cutting Angle Cutting Feed Rate by spring holding The machine uses a swivel miter base for angle cutting from 0 ~ 60 degree. On the sawing arm, Turn toggle switch to down location. Select there is an attached scale (Q) in Fig.7. This spring as outer location. -
Page 11: Magnetic Switch
Remove the blade guard by loosening two Remove blade from both wheels and blade screws (U) in Fig. 9 on the saw frame. guides bearings (X) in Fig.12. Fig. 12 Fig. 9 Place a new blade on the wheels but not Remove blade cover by loosening four too tight, twist blade slightly and let it slip screws (V) in Fig.10 on the saw frame. -
Page 12: Adjustment
8. Adjusting Adjusting Blade Guide An unbounded handle (A) in Fig.14 is mounted on the unit for freely changing blade guide device position by loosens it counter- clockwise. Fig. 15 Fig. 14 It’s designed for your convenience to adjust blade guide easily and quickly at any time, and under any situation. -
Page 13: Adjust Assistant Plate
Carbon brush Fig. 17 Fig. 22 Adjust Assistant Plate This assistant plate can move depend on Fig. 18 material length. If the working piece is longer than vise, adjust assistant plate (Fig. 23, A) location to support working piece. It offers the support point while cutting. -
Page 14: Part List & Explosion Drawings
- 12 -... - Page 15 - 13 -...
- Page 16 - 14 -...