Specifications M•2600 - Mackie M-2600 Owner's Manual

SPECIFICATIONS
M•2600
Maximum Power at 1% THD, midband:
500 watts per channel into 8Ω
850watts per channel into 4Ω
1300 watts per channel into 2Ω
1700 watts into 8Ω bridged
2600 watts into 4Ω bridged
Continuous Sine Wave Average Output Power,
both channels driven:
425 watts per channel into 8Ω from 20Hz to 20kHz,
with no more than 0.025% THD
700 watts per channel into 4Ω from 20Hz to 20kHz,
with no more than 0.05% THD
1000 watts per channel into 2Ω from 20Hz to 20kHz,
with no more than 0.1% THD
Bridged mono operation:
1,400 watts into 8Ω from 20Hz to 20kHz, with no more
than 0.05% THD
2000 watts into 4Ω from 20Hz to 20kHz, with no more
than 0.1% THD
Note: Power ratings are specified at 120VAC line voltages.
The M•2600 power amplifier draws large amounts of
current from the AC line with continuous sine wave test-
ing. Accurate measurement of power requires a steady
and stable AC supply. This means the line impedance
must be very low to insure that the peak AC line voltage
does not sag to less than 97% of its value.
If driving highly reactive loads, we recommend that the
limiter circuit be engaged.
Power Bandwidth:
20Hz to 70kHz (+0, –3 dB) @ 700W into 4Ω
Frequency Response:
20Hz to 40kHz (+0, –1 dB)
10Hz to 70kHz (+0, –3 dB)
Distortion:
THD, SMPTE IMD, TIM < 0.025% @ 8Ω
< 0.050% @ 4Ω
< 0.150% @ 2Ω
Signal-to-Noise Ratio:
> 107 dB below rated power into 4Ω
Channel Separation:
> 80 dB @ 1kHz
Damping Factor:
> 350 @ 400Hz
Input Impedance:
24kΩ balanced
Input Sensitivity:
1.23 volts (+4 dBu) for rated power into 4 ohms
Gain:
32.7 dB (43V/V)
Maximum Input Level:
9.75 volts (+22 dBu)
40
Rise Time:
< 5µs
Slew Rate:
Voltage Slew Rate > 60V/µs
Current Slew Rate> 30A/µs at 2Ω
CMRR:
> 40 dB, 20Hz to 20kHz
Load Angle:
8(±jx) time independent at 8Ω
4(±jx) time dependent, T > 6 min. at 4Ω
2(1±jx) time dependent, T > 2 min. at 2Ω
Transient Recovery:
< 1µs for 20 dB overdrive @ 1kHz
High Frequency Overload and Latching:
No latch up at any frequency or level.
High Frequency Stability:
Unconditionally stable, driving any reactive or
capacitive load.
Turn On Delay:
3-5 seconds
Variable Low-Cut Filter:
10Hz (Off) to 170Hz, 2nd-Order Bessel
Internal Crossover:
Switched: 60Hz/90Hz/120Hz, 4th-Order Linkwitz-Riley
Lowpass outputs switchable to internal Subwoofer
mode.
Lowpass and Highpass outputs switchable to Thru
output jacks.
Limiter Section:
Complementary Positive and Negative Peak Detecting
Indicators:
6 meter LEDs per channel
SIG (Signal Present), –20, –9, –6, –3, OL (Overload)
CH 1 & 2
PROTECT LEDs
SHORT LEDs
TEMP STATUS
COLD/HOT LEDs
Physical: (lets get)
(three rack spaces high, standard rack width)
Height 5.20 inches
Front panel Width 19.00 inches
Chassis Width 17.24 inches
Depth 15.65 inches
Overall Depth 16.67 inches
Weight 55 pounds
AC Drop-out Voltage:
At approximately 63% of rated line voltage
(132mm)
(483mm)
(438mm)
(398mm)
(423mm)
(25 kg)