Related Manuals for Zanussi ZWG 680P
Summary of Contents for Zanussi ZWG 680P
- Page 1 User manual Washing Machine ZWG 680P ZWG 6100P Downloaded From WashingMachine-Manual.com Manuals...
-
Page 2: Table Of Contents
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4... - Page 3 not pressing the electrical supply cable against the • The detergent dispenser drawer is provided with an in- wall. sert for liquid detergent. Do not use the insert down- wards for gelatinous detergents, with programmes in- • Install the appliance on a flat hard floor. cluding prewash, with the delay start option.
-
Page 4: Frost Precaution
To activate this device, ro- To disable this device and tate the button (without restore the possibility of pressing it) inside the closing the door, rotate the door clockwise until the button anti-clockwise until groove is horizontal. If the groove is vertical. necessary use a coin. -
Page 5: Product Description
>PP<=polypropylene • The machine works more economically if it is fully loa- This means that they can be recycled by disposing of ded. them properly in appropriate collection containers. • With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a Ecological hints lower temperature. -
Page 6: Installation
0,05 MPa Maximum 0,8 MPa Maximum Load Cotton 6 kg Spin Speed Maximum 800 rpm (ZWG 680P) 1000 rpm (ZWG 6100P) Installation Unpacking Warning! • Read carefully the "Safety information" chapter before installing the appliance. • Remove the cardboard top. - Page 7 • Open the door and re- Warning! Do not re- move the plastic hose move the drain hose guide, the bag contain- from the rear support. Re- ing the instruction move this hose only if it is booklet and the plastic necessary to drain the wa- plug caps from the ter.
- Page 8 Positioning and levelling 35° 45° Loosen the ring nut to angle the hose to the left or right depending on the position of your water tap. Do not place the inlet hose downwards. After positioning the inlet hose, be sure to tighten the ring nut again to pre- vent leaks.
- Page 9 • Directly to a built-in drain pipe in the room wall. Push the drain hose onto the spigot and secure with a clip, ensure a loop is formed in the drain hose to pre- The drain hose may be extended to a maximum of 4 vent waste from the sink entering the appliance.
-
Page 10: First Use
• Always use a correctly installed shockproof socket. • Make sure that the mains plug is accessible after in- stallation. • Do not use multi-way plugs, connectors and extension cables. There is a risk of fire. • Do not pull the mains cable to disconnect the appli- ance. - Page 11 Tar stains: first treat with stain remover, methylated spirits All commonly available washing machine detergents may or benzine, then rub with detergent paste. be used in this appliance: • powder detergents for all types of fabric, Open the door by carefully pulling the door handle •...
- Page 12 UP- Flap position if using DOWN - Flap position if • Rotate the flap down- POWDER detergent using LIQUID detergent wards. during main wash • Carefully put the drawer back. • Measure out the detergent. For the quantity of detergent, refer always to what is written on the product packing and ensure that If the flap is not in the desired position: the detergent can be poured in the drawer.
- Page 13 Set your washing programme The control panel permits to select a washing programmes and different options. When an option button is selected, the corresponding pilot light is on. Otherwise it is off. For compatibility among washing programmes and options, see the "Washing Programme Chart". If an incorrect option is selected, the integrated red pilot light of the button 6 flashes 3 times.
- Page 14 By selecting a programme, the appliance proposes automatically the maxi- Automatic Spin reduction and mum spin speed provided for that programme. Rinse Hold By selecting Automatic Spin reduction the spin speed is reduced to a half, but not less than 400 rpm. The relevant light illuminates. AUTO Rinse Hold By selecting this function the water of the last rinse is not emptied out to...
- Page 15 The start of the programme can be delayed by 9, 6 or 3 hours by means of this button. The relevant light illuminates. You must select this option after you have set the programme and before you start the programme. Select a delayed start: •...
-
Page 16: Washing Programmes
(Cold) RINSE HOLD, Main wash - Rinses - Maximum spin speed at: 800 rpm for model DELAY START, ZWG 680P; 1000 rpm for model ZWG 6100P Max. load 6 kg - Reduced load 3 kg SUPER QUICK EXTRA RINSE White, coloured cotton and linen. Normally soiled items. - Page 17 RINSE HOLD, Prewash - Main wash - Rinses - Maximum spin speed at: 800 rpm DELAY START, for model ZWG 680P; 1000 rpm for model ZWG 6100P SUPER QUICK Max. load 6 kg - Reduced load 3 kg EXTRA RINSE White, coloured cotton and linen.
- Page 18 40°- (Cold) Main wash - Rinses - Maximum spin speed: at 800 rpm for model AUTOMATIC SPIN RE- ZWG 680P; 1000 rpm for model ZWG 6100P DUCTION, Max. load 2 kg RINSE HOLD, Machine washable wool, hand washable woollens and delicate fab- DELAY START rics with «hand washing»...
-
Page 19: Consumption Values
60°- Cold AUTOMATIC SPIN RE- Main wash - Rinses - Maximum spin speed at: 800 rpm for model DUCTION, ZWG 680P; 1000 rpm for model ZWG 6100P RINSE HOLD, Max. load 3 kg DELAY START Trousers, shirts or jackets in denim and jersey realized with hi-tech materials. - Page 20 To run a maintenance wash: • Use the previous brush • The drum should be empty of laundry. to clean the recess, en- • Select the hottest cotton wash programme. suring that upper and • Use a normal measure of detergent, must be a powder lower part of it is well with biological properties.
-
Page 21: What To Do If
• close the filter cover; • insert the mains plug again. • remove the filter and clean it under the tap; Cleaning the water inlet filters • if necessary, place the Important! If the appliance doesn't fill, it takes a long time filter cover in the right to fill with water, the starting button flashes red or the position again. - Page 22 lights illuminates to indicate that the appliance is not Before contacting your local Service Centre, please carry working. out the checks listed below. Fault code and malfunction Possible cause / Solution The water tap is closed. • Open the water tap. The inlet hose is squashed or kinked.
- Page 23 Fault code and malfunction Possible cause / Solution The door has not been closed or is not closed properly. • Close firmly the door. The light of button 6 flashes and the light 7.3 illuminates: Door open The appliance does not start or stops during operation Before contacting your local Service Centre, please carry without any visible alarm.
- Page 24 Malfunction Possible cause / Solution The programme is still running. • Wait the end of washing cycle. The door lock has not been released. The door will not open: • Wait until the door lock is released. There is water in the drum. •...
- Page 25 The necessary data for the service centre is on the rat- ing plate. We recommend that you write the data here: Mod..Prod. No..Ser. No..Model description ....... (MOD.) Product number (PNC) .......
- Page 26 Downloaded From WashingMachine-Manual.com Manuals...
- Page 27 Downloaded From WashingMachine-Manual.com Manuals...
- Page 28 Downloaded From WashingMachine-Manual.com Manuals...