Sony dvp-s3000 Service Manual page 49

How to see Emergency History
1 2 3
1 EMG CODE
2 MECH MODE
3 DISC
4 TIME (MSB)
5 TIME
6 TIME (LSB)
1 EMG CODE
a) Drvcon emergency code list
Initial
00: No Emergency
01: RAM check NG (IC138)
02: ROM check NG (ICS140)
03: EEPROM RW NG (IC139)
04: EEPROM BUSY Time Out (IC139)
05: CXD2545 (IC717) check NG
06: CXD8599 (IC710) check NG
07: CXD8663 (IC181) check NG
08: HYDET NG
09: SDCNTL NG
0A: VCO NG
0B: Focus Gain Adj NG
0C: Trk Gain Adj NG
0D: Jitter NG
Door & Tray system
10: Door Time Out
11: Tray Time Out
Spindle system
20: Spindle Lock Time Out
21: Spindle Out of Control
Sled system
30: Home Position Time Out
31: Sled FG NG
32: Sled Drv NG
Tilt system start up/down
50: Focus Search Time Out
Trace system
60: CL VLOCK NG
61: PLL NG
62: Address Continuity NG
63: PLL Lock Time Out
64: CLV Lock Time Out
65: Layer slip NG
Seek system
70: Address Read NG
71: Seek NG
72: Focus Jump NG
73: TOC Read Time Out
74: FOK NG
75: Req Address NG
76: Req Time NG
77: Req Track No NG
5 6
4
DVD : Selector address
CD : minute & second frame
Communication system
80: Communication NG
(b) Syscon emergency codes list
Stop system
10: Stop request from drive controller was received
11: At the mode change command, the mode could not be
changed within specified time and the drive stopped.
12: Retry due to supply error failed and the drive stopped.
13: Disc directory configuration and information file are ille-
gal and the drive stopped.
14: The drive stopped as a DVD-R disc was used.
15: Coded data could not be decoded and the drive stopped.
16: At slow R, the destination of reverse search is illegal and
the drive stopped.
17: Information file reading failed and the drive stopped.
Retry system
20: Disc data reading failed and retry was made.
21: Video decoder operation failed and retry was made.
22: Retry was made due to DMX error.
23: At slow R, retry was made due to data supply time out.
24: At slow R, retry was made due to wrong Navi Pack address.
25: At slow R, video decoder operation failed and retry was made.
26: At slow R, retry was made due to failure of display pic-
ture preparation.
27: At FF/FR, retry was made due to data supply time out.
28: At FF/FR, video decoder operation failed and retry was made.
Power system
80: The power turned off because of power off request from
drive controller
81: The mode change to Stop mode failed and the power
turned off.
2 MECH MODE (Drvcon Mech mode list)
00: Power ON Ready (immediately after power on)
10: Eject
20: Stop
30: Trace (data supply mode)
40: Pause
50: Scan
60: Mecha Initialize
70: Load
80: Unload
90: Spin Up (disc startup operation)
A0: Spin Down (disc stop operation)
B0: Seek (search mode)
C0: Error Recovery
D0: Service
3 DISC (Drvcon status list)
bit
0: DVD/CD
1: 12cm/8cm
2: Layer
3: Reflectivity
4: Judge/No judge Judge
5: Disc/No disc
6: CDROM
7: Track Density (DVD)
Note: If judge/no judge is not "judge", correct data have not been
written.
6-19
6-19 E
Value:0 Value:1
DVD CD
12cm 8cm
Single Dual
High Low
No judge
Disc No disc
Not True
0.74 mm 0.80 mm