Programming The Clock - Breville BDC650 the Grind Control Instruction Book

OPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCT
3. Select 'Single Cup' Mode
Press the CUP|CARAFE dial until the LCD
screen displays the CUP symbol and the
current cup size selected in ounces. Rotate the
CUP|CARAFE dial to select the required size.
There are 7 size options to accommodate
for different amounts or milk, half-and- half
and creamer. Always ensure your cup is an
adequate size for the setting selected.
The amounts displayed on the LCD screen
are approximate only. Actual amounts may
vary depending on the type of filter used, the
coffee grind size, roast, blend and freshness, or
amount and type of pre-ground coffee used.
4. Select the Brew Strength or
'PRE-GROUND' Coffee Setting
There are 8 strength settings. The LCD screen
will display the current strength setting. Rotate
the STRENGTH dial to select your required
strength. 1 is the weakest and 8 is the strongest.
We recommend starting on setting 4 for a
medium strength coffee. Adjust strength
higher or lower to suit your taste.
NOTE
If using pre-ground coffee, select the
'PRE-GROUND' coffee setting. This will
disable the grinder. Add pre-ground
coffee to the gold tone filter or a paper
filter. We recommend 1 level tablespoon
of pre-ground coffee per 5oz/150ml cup
of water. Adjust the amount according
to your individual taste. The maximum
capacity for pre-ground coffee is 12 level
tablespoons. Exceeding this amount may
cause overflow.
16
5. Start the Brew Cycle
Press the START | CANCEL button.
The grinder will commence grinding the
correct amount of coffee for the selected brew
size and strength. If the 'PRE-GROUND'
coffee setting has been selected, the grinder
will be disabled.
NOTE
Steam may emit from the rear steam vent
during grinding and brewing. This is
normal.
The count-down timer will then begin. The
time displayed is an estimate only and will
depend on the amount and strength settings
you have selected. The LCD screen will display:
a) 'PRE-HEATING' as the water is heated
to the optimal temperature. The
pre-heating time will depend on the
starting temperature of the water in
the water tank.
b) 'INFUSING' as coffee and water are
steeped together.
OPERATING YOUR BREVILLE PRODUCT OPERATING YOUR BREVILLE PRODUCT
c) 'BREWING' as the coffee is dispensed
into the cup.
To stop the cycle at any time, press the
START | CANCEL button. You will hear
a winding noise. This is normal.
CAUTION
Never open the swing-out door and
remove the coffee basket while brewing.
Hot water and coffee can cause injury.
6. Empty the Coffee Basket
Once the brewing cycle is complete, the ready
signal will sound and a winding noise will be
heard. This is normal.
The coffee machine will automatically shut-off,
however the LCD screen will flash 'EMPTY
COFFEE FILTER' as a reminder to remove
the coffee basket and discard the used grinds.
Wash the coffee basket, taking particular care
to rinse the chute area. Then dry the coffee
basket and chute area thoroughly.
We also recommend checking the coffee
grinds chute disc for any build-up of coffee
grinds. This is the stainless steel disc that is
visible when the swing-out door is opened.
A build-up of grinds on this disc can affect the
performance of the machine. Wipe the disc
clean then dry thoroughly.
CAUTION
The coffee basket, gold tone or paper
filter may still be very hot after brewing.
Use caution and allow to cool before
removing.
NOTE
If using the gold tone filter, you may
notice the brewing cycle finish before
the ready signal sounds. This is normal.
The total brewing time displayed on the
LCD screen is calculated using paper
filters as coffee passes through paper
filters slower.

PROGRAMMING THE CLOCK

(OPTIONAL)
1. Press the MENU|EXIT button.
2. Press the STRENGTH dial. The LCD
screen displays the current time,
flashing.
3. Rotate the STRENGTH dial to adjust
the time.
4. Press the STRENGTH button to set.
The machine will beep to confirm.
5. The LCD will return to the main screen
when the clock is set.
PROGRAMMING AUTO START
(OPTIONAL)
The Auto Start feature allows you to program
the specific time when the coffee machine will
automatically turn on and start the grinding
and brewing cycle.
You must set the clock to use the Auto Start
feature. Always remember to reset the clock for
time changes, power outages and when you
unplug the machine.
1. Press the AUTO START button.
The current Auto Start time will be
displayed and flashing.
17