Cooling With Fan Convectors Vitoclima 200-C (Accessory); Heat Pump Control Unit Cd 70; Accessories; Vitotrol 200 - Viessmann VITOCAL 200-G Technical Manual

Design information
(cont.)

Cooling with fan convectors Vitoclima 200-C (accessory)

■ Cooling operation possible either via separate cooling circuit or via
a heating/cooling circuit. For max. cooling capacity, select operating
mode "Fixed value".
■ Select an installation location where the heat pump can be easily
connected.
■ Consider the connection of the condensate drain to the domestic
drainage system or routing the condensate to the outside of the
building.
■ Power supply (1/N/PE,230 V/50 Hz) required.
■ When creating wall outlets, consider supports, lintels and sealing
elements (e.g. vapour barriers).
■ Only fit appliances to solid level walls.
■ Never install appliances near heat sources or places subject to direct
solar irradiation.
■ Install appliances only in locations with good air circulation.
■ Ensure easy accessibility for service.
Speed-dependent heating and cooling capacities
Type Fan speed Air flow Cooling mode
rate Total cooling
capacity
3
m /h W
V1 292
V2 260
V202H V3 205
V4 163
V5 122
V1 524
V2 433
V203H V3 354
V4 323
V5 272
V1 843
V2 708
V206H V3 598
V4 545
V5 431
V1 1266
V2 983
V209H V3 859
V4 730
V5 612
Factory-set fan speed

Heat pump control unit CD 70

7.1 Accessories

Vitotrol 200

Part no. 7450 017
KM BUS subscriber
The Vitotrol 200 remote control regulates the heating program for one
heating circuit and the required set room temperature in standard
mode, from any room in the house.
The Vitotrol 200 is equipped with backlit heating program selection
keys as well as a party and economy key.
The fault display shows faults on the control unit.
WS function:
Installation anywhere in the building.
RS function:
Installation in the main living room on an internal wall opposite radia-
tors. Never install inside shelf units, recesses, immediately by a door
or heat source (e.g. direct sunlight, fireplace, TV set, etc.).
VITOCAL 200-G
Output matching
The output of fan convectors can be modified. By changing the termi-
nal connections, 3 of the available 5 speeds can be assigned to the
three-stage speed selector of the fan convectors.
The heating and cooling capacities available with the respective
speeds are shown in the following table.
Test conditions
■ Cooling capacity:
At 27 °C room temperature, 48% relative humidity, cooling the cool-
ing water from 12 to 7 °C.
■ Rated output:
At 20 °C room temperature, flow temperature 50 °C.
■ Sound pressure level
Measured at a distance of 2.5 m with a room volume of 200 m
a reverberation time of 0.5 s.
Sensible Flow rate Pressure
cooling
capacity
W l/h
1971 1518 338
1846 1390 317
1543 1141 266
1327 954 227
1075 755 184
3398 2663 583
3007 2289 515
2560 1920 439
2409 1784 414
2128 1550 367
5614 3770 961
4836 3200 828
4289 2796 735
3984 2581 684
3305 2168 569
8833 6708 1516
7402 5464 1271
6491 4779 1113
5537 4076 951
4627 3407 792
The integral room temperature sensor captures the actual room tem-
perature and effects any necessary correction of the flow temperature
as well as a rapid heat-up at the start of the heating operation (if
appropriately programmed).
Connection:
■ 2-core lead, length max. 50 m (even if connecting several remote
control units)
■ Never route this lead immediately next to 230/400 V cables
■ LV plug part of the standard delivery
Heating mode
Heating Flow rate Pressure
drop output
kPa W l/h
42 2463 216
37 2370 208
27 2102 184
20 1812 159
14 1470 129
31 4544 398
25 4227 371
19 3732 327
17 3517 309
14 3207 281
40 6651 583
31 6091 534
25 5614 493
22 5327 468
16 4589 403
38 11558 1014
28 10251 899
22 9429 828
16 8141 714
12 6745 592
3 and
Sound
pressure
drop level
kPa dB(A)
6 42
5 38
4 32
3 25
2 23
25 41
22 36
17 31
16 29
13 26
15 50
13 45
11 41
10 38
8 31
48 55
38 48
33 45
25 42
18 38
7
VIESMANN
47