Safety precaution ! CAUTION Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. ! CAUTION Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 3
Preventing static electricity 1.Grounding to prevent damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 2.About the earth processing for the destruction prevention by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Disassembly method Removing the front panel unit (See Fig. 1, 2) 1.Press the Eject button to open the front panel unit 2.Push and open the right and left open/close shaft arms outward to remove the shaft. Front panel unit Eject button 3.Remove the front panel unit from the same side as the...
Page 5
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Removing the main board(wiht rear panel) (See Fig. 6, Fig. 7) 1.Remove three screws E retaining the rear panel to the chassis 2.Remove one screw C retaining the IC to the heat sink. 3.Remove two screws D retaining the main board.
Page 6
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Damper bracket Removing the CD mechanism control CD mechanism ass’y board (See Fig.1 and 2) Unsolder the part f and g on the CD mechanism control board. Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part).
Page 7
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Removing the loading motor Loading motor (See Fig.3 to 5) Prior to performing the following procedure, remove the CD mechanism control board. Belt Remove the two springs k attaching the CD mechanism ass’y and the front bracket. Fig.5 Remove the two screws G and the front bracket while pulling the flame outward.
Page 8
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Removing the feed motor ass’y Part n FD screw (See Fig.10) Feed motor ass’y Prior to performing the following procedure, remove the CD mechanism control board, the front bracket Part O (loading motor) and the CD mechanism ass’y.
6. Digital tester MW 522kHz ~ 1620 kHz 7. Tracking offset meter LW 144kHz ~ 279kHz 8. Test Disc JVC :CTS-1000 9. Extension cable for check EXTGS004-26P 1 Dummy load Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered...
Page 10
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Flow of functional operation until TOC read Power ON • When the laser diode correctly Set Function to CD • When the pickup correctly moves emits to the inner area of the disc Microprocessor Microprocessor Disc inserted commands commands TC9462 "53"...
Page 11
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Feed Section Check CD 9V Is the voltage output at Is the wiring for IC521 Is 5V present at IC581 and 5V. IC521 pin "53" 5V or 0V? (90) ~ (100) correct? pin "11"? Check the vicinity of IC521.
Page 12
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens with a alcohol soaked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear.
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Description of major ICs UPD784215GC-158 (IC701) : CPU 1.Terminal Layout 2.Pin Function (1/2) Function Symbol Pin No. Detection switch of CD mechanism Detection switch of CD mechanism Detection switch of CD mechanism Reset signal input from CD mechanism...
Page 14
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R Pin Function (2/2) Function Symbol Pin No. BUSSI J-BUS data input BUSSO J-BUS data output BUSSCK J-BUS Clock signal I/O BUSI/O I/O selector output for J-BUS, H:OUT L:IN LCDDA Data output to LCD driver LCDSCK Clock output to LCD driver...
Page 15
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R LA6557-X(IC501):Driver 1.Terminal layout 2.Block diagram CH3,4,5 Thermal shutdown VCC2 POWER V05- V05+ S-GND MUTE is as follows: High : Output ON Low : Output OFF V04+ MUTE MUTE V04- VIN+ V03+ VIN4- V03- VCC-S Signal System Power V02+...
Page 16
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R 3.Pin function LA6557-X(2/2) Pin NO. Symbol Function VCC2 Power for channels 3,4, and 5 (VCC1 and VCC-S short-circuited) V05- Loading output (-) V05+ Loading output (+) V04+ Output pin (+) for channel 4 V04- Output pin (-) for channel 4...
Page 17
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R TC9462F (IC541) : DSP & DAC 1.Pin Layout 2.Pin Function (1/2) Symbol Function Pin No. Test mode terminal. Normally, keep at open TEST0 Playback speed mode flag output terminal Playback speed mode flag output terminal UHSO Sub code Q data emphasis flag output terminal. "H"=ON "L"=OFF EMPH Channel clock output terminal.(44.1kHz) "H"=Rch "L"=Lch...
Page 18
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R 2.Pin Function (2/2) Symbol Function Pin No. RFRP signal center level input terminal RFCT RFRP zero cross input terminal RFZI RF ripple signal input terminal RFRP Focus error signal input terminal Sub-beam adder signal input terminal SBAD Test input terminal Normally, keep at "vref" level TSIN Tracking error signal input terminal.
Page 19
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R 24LC16B-I/SN-X (IC771) : EEPROM 1. Pin layout 2. Block diagram HV GENERATOR MEMORY EEPROM ARRAY CONTROL CONTROL XDEC (8x256x8) LOGIC LOGIC PAGE LATCHES YDEC SENSE AMP R/W CONTROL 3. Pin function Symbol Function Ground Serial address/data I/O Serial clock Write protect input +2.5V to 5.5V power suply...
Page 20
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R BA4905-V3 (IC901) : Regulator 1.Terminal layout 2.Block diagram REGULATOR RESET RESET COMP VDD 5.7V CD 8V AUDIO 9V CTRL ILM 10V 3.Pin function Pin no. Symbol Function RESET If VDD voltage becomes 4V or less.RESET output becomes low level.
Page 21
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R IC-PST600M/G/-W (IC702) : System reset Vout HD74HC126FP-X (IC801) : Buffer 1. Pin layout 2. Function Inputs Outputs 3. Block diagram Output Input Output Sample as Load Circuit 1 Output Sample as Load Circuit 1 Output Sample as Load Circuit 1...
Page 23
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R LC75873NW (IC601) : LCD driver 1.Block Diagram VDD1 COMMOM SEGMENT DRIVER DRIVER VDD2 CLOCK SHIFT REGISTER GENERATOR ADDRESS DETECTOR 2.Pin Functions Pin No. Symbol Description 1~66 S3~S68 Segment Output. 67~69 COM1~3 Common Driver Output. Power Supply Connection. VDD1 Used for applying the LCD drive 2/3 bias voltage externally.
Page 24
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R NJM2100M-WE (IC861) : Cruise 1. Pin layout A OUTPUT A -INPUT B OUTPUT A +INOUT B -INPUT B +INPUT 2. Block diagram -INPUT OUTPUT +INPUT NJM4565M-WE (IC581) : Ope. amp A OUTPUT B OUTPUT A INPUT A INPUT...
Page 26
KD-SX979R/KD-SX925R KD-SX924R/KD-SX909R SAA6579T-X (IC71) : RDS demodulator 1. Pin layout 2. Pin function Symbol Function QUAL Quality indication output RDDA RDS data output Vref Reference voltage output (0.5VDDA) Multiplex signal input VDDA +5V supply voltage for analog part VSSA Ground for analog part (0V)
PARTS LIST [KD-SX979R/KD-SX925R] [KD-SX924R/KD-SX909R] * All printed circuit boards and its assemblies are not available as service parts. Area suffix E ----------- Continental Europe - Contents - Exploded view of general assembly and parts list 3- 2 CD mechanism assembly and parts list...
Page 35
Exploded view of general assembly and parts list Block No.
Page 36
Area ZCKDSX909R-NPA NOSE PIECE 1 KD-SX909R ZCKDSX924R-NPA NOSE PIECE 1 KD-SX924R ZCKDSX925R-NPA NOSE PIECE 1 KD-SX925R ZCKDSX979R-NPA NOSE PIECE 1 KD-SX979R FSJC1058-001 FRONT PANEL FSJD3024-01F FINDER ASSY 1 KD-SX979R FSJD3024-01G FINDER LENS 1 KD-SX909R FSJD3024-01H FINDER LENS 1 KD-SX925R FSJD3024-01J...
Page 37
(General assembly) Parts list Block No. M1MM Description Item Parts number Parts name Q'ty Area FSKS3013-001 LENS CASE QNZ0449-001 RUBB.CONNECTOR QNZ0450-001 RUBB.CONNECTOR FSYH4061-001 LIGHT SHEET KD-SX 909R/924R/979R 1 KD-SX925R FSYH4061-003 LIGHT SHEET FSKS3017-002 L.E.D.HOLDER FSJC1061-001 FRONT CHASSIS FSXP3060-001 RELEASE LEVER FSKW3002-016 COMP.SPRING 1 FOR RELEASE KNO...
Page 38
CD mechanism assembly and parts list Block No. Grease G-31SA G-31SA(Bottom side) RX-405 106 29...
Page 39
(CD mechanism) Parts list Block No. M2MM Parts number Parts name Q'ty Description Item Area 30310101T FRAME 30310103T DANPER PIN 30310107T UPPER PLATE 30310108T SEL STOP PLATE 30310142T SEL ARM (L)L 30310143T SEL ARM (R)L 30310145T S ARM SPRING(L) 30310112T TRIG LEVER 30310155T TRIG PL(Z)
Page 40
(CD mechanism) Parts list Block No. M2MM Parts number Parts name Q'ty Description Item Area 30311035T FPC HOLDER(Z) 19501403T WIRE CLAMPER 30311037T PICK UP FPC(Z) 30311036T CONNECT.PCB(Z-J 30311038T WIRE (5P-Z) 30311039T WIRE (LD-Z) 30311040T WIRE (FD-Z) 30311041T WIRE (RS-Z) 64180402T DET SWITCH 2 ESE22MH1 64180403T...
Page 41
Parts list (CD mechanism) Block No. M2MM Parts number Parts name Q'ty Description Item Area 303111302T ROLLER SHAFT 303111302T ROLLER SHAFT 303105502T T.T.BASE ASSY...
Page 42
c cc cvvv (Main board) Electrical parts list Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 241 QEKJ1HM-105Z E.CAPA I.M 1.0MF 20% 50V BZ841 QAN0009-001Z BUZZER C 242 QEKJ1CM-226Z E.CAPA I.M 22MF 20% 16V QEKJ1CM-226Z E.CAPA I.M...
Page 43
SB DIODE C 781 QEKJ0JM-476Z E.CAPA I.M 47MF 20% 6.3V D 972 CRS03-W SB DIODE C 782 NCB21EK-823X C CAPACITOR KD-SX979R D 991 CRS03-W SB DIODE C 784 QEKJ1CM-107Z E.CAPA I.M 100MF 20% 16V D 992 CRS03-W SB DIODE C 801...
Page 44
(Main board) Electrical parts list Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area UN2111-X TRANSISTOR R 163 NRSA02J-222X MG RESISTOR Q 31 UN2211-X TRANSISTOR R 164 NRSA02J-473X MG RESISTOR Q 51 2SC2412K/R/-X TRANSISTOR R 165...
Page 45
(Main board) Electrical parts list Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 756 NRSA02J-473X MG RESISTOR R 555 NRSA02J-332X MG RESISTOR R 757 NRSA02J-222X MG RESISTOR R 556 NRSA02J-682X MG RESISTOR R 758 NRSA02J-473X...
D 657 MA3056/M/-X ZENER DIODE CN601 QNZ0006-001 CAR CONNECTOR EN601 QSW0863-001 JOG SHUTTLE SW D 601 SML-310LT/MN/-X IC601 LC75873NW D 602 LNJ308G81/1-3/X KD-SX979R/909R IC602 RPM6938-SV4 D 602 SML-310VT/JK/-X KD-SX924R/925R Q 641 2SB815/7/-X TRANSISTOR D 603 SML-310VT/JK/-X KD-SX924R/925R Q 642 UN2211-X TRANSISTOR...
Page 47
(Switch board) Electrical parts list Block No. 02 Item Parts number Parts name Remarks Area S 601 NSW0066-001X TACT SWITCH S 602 NSW0066-001X TACT SWITCH S 603 NSW0066-001X TACT SWITCH S 604 NSW0066-001X TACT SWITCH S 605 NSW0066-001X TACT SWITCH S 606 NSW0066-001X TACT SWITCH...
Page 48
Packing materials and accessories parts list Block No. Block No. KIT2: A10,A11, KIT1:A5~A9 A17,A21 SCREW KIT 2 A3: Remocon : Screw : Sheet : Sheet A4 : Battery...
Block No. M3MM Description Item Parts number Parts name Q'ty Area FSPE3001-171 PACKING CASE 1 KD-SX924R FSPE3001-176 PACKING CASE 1 KD-SX979R FSPE3001-170 PACKING CASE 1 KD-SX925R FSPE3001-172 PACKING CASE 1 KD-SX909R PAPER CUSHION FSPH1018-002 VPE3005-064 POLY BAG QPA01703505P POLY BAG FOR INST.
Page 50
A 12 FSJB3001-00A HARD CASE A 13 FSKM2004-002SSF MOUNTING SLEEVE A 14 QAM0158-001 CAR PLUG CORD KD-SX 979R/925R/924R QAM0160-001 CAR CABLE 1 KD-SX979R A 16 FSJD2034-001 TRIM PLATE A 17 FSUN3115-T481 INSTALL MANUAL SWE,FIN FSUN3115-T451 INSTALL MANUAL DUT,SPA,ITA FSUN3115-T211 INSTALL MANUAL...