Advanced System Programming - Linear RE-1 Installation, Programming And Operation Instructions

Call Forwarding Feature
The call forwarding feature will allow a visitor to contact the resident at
the programmed telephone number instead of through the local telephone
line. The feature can be set to be active during a selected Time Zone or
at all times. The telephone number programmed can contain an extension
number and an optional time delay before dialing the extension.
Press:
Telephone Number
Forwarding: 0 = Call forwarding feature OFF
1 = Call forwarding feature ON at all times
2 = Call forwarding feature ON (scheduled by Time Zone)
3 = Forward the call if there was no resident answer
Time Zone = 1-7 (Call forwarding feature active during this Time Zone)
Telephone Number = Up to 11-digit telephone number
Extension = Up to 4-digit telephone extension number
Delay = 1-25 seconds (delay between telephone number and extension)
Example, call forwarding with only a phone number:
Press: or
A special feature is implemented for "Ring Down" PBX systems. If no
telephone number is programmed and call forwarding is enabled, the unit
will connect immediately without dialing.
Example, call forwarding with extension and no time zone:
Press:
Extension
Example, call forwarding scheduled by time zone:
Press:
Extension
NOTE: Time zone is only used with forwarding = 2
Example, call forwarding off:
Press:
Alternate Resident Telephone Numbers
For installations where multiple residences exist behind shared controlled
access, the RE-1 can dial three alternate telephone numbers. The visitor can
call an alternate number by entering "1#", "2#", or "3#" on the main keypad.
Press:
Telephone Number
Location: 1 = "1#" location; 2 = "2#" location; 3 = "3#" location
Enable: 0 = Disable; 1 = Unconditionally enable
Telephone Number: Up to 11-digit telephone number
Extension: Up to 4-digit telephone extension number
Delay: 1-25 seconds (delay between telephone number and extension)
22
Default: OFF
Forwarding Time Zone
Extension Delay
Telephone Number
or Telephone Number
Delay
Time Zone Telephone Number
Delay
Default: All Disabled
Location Enable
Extension Delay
Resident Response Telephone Keys
Key D "6" = Switch To/From Call Waiting
The resident response keys are the telephone keys that the resident uses to
grant access and control calls from a visitor. The keys for the four functions
can be customized. Enter all four keys each time this programming PPN is
used.
Press:
Keys ABCD: Enter 4 digits for the response keys A, B, C, & D
Key A = Activates Relay #1
Key B = Activates Relay #2
Key C = Disconnects the Visitor's Call
Key D = Switches to and from a call holding on call waiting
Resident Programming and Command Prefi xes
The resident command prefi x is entered on a local telephone prior to
entering a command number to control one of the relays or open voice
communications with the RE-1. The resident programming prefi x is entered
on a local telephone or the main keypad prior to programming the RE-1.
Press: Programming
Programming: 0 = "###"; 1 = "***"; 2 = "*#*"; 3 = "#*#"
Command: 0 = "##"; 1 = "**"; 2 = "*#"; 3 = "#*"

ADVANCED SYSTEM PROGRAMMING

Reset System Defaults
The system can be reset back to the factory defaults with this programming
PPN. EXECUTING THIS PPN WILL NOT ERASE ANY ENTRY CODES OR
TRANSMITTERS THAT HAVE BEEN PROGRAMMED.
Press:
Relay #1 On Time
Changes the length of time Relay #1 activates when triggered.
Press:
Seconds = Output time in seconds 0-60
Relay #2 On Time
Changes the length of time Relay #2 activates when triggered.
Press:
Seconds = Output time in seconds 0-60
Main & Remote Keypad Relay and Time Zone
Default: Main Keypad = Set by Entry Code, No Time Zone
Remote Keypad = Relay #2, No Time Zone
Sets the relay and time zone that the main and remote keypad will use.
Press: Keypad
Keypad: 1 = Main Keypad
2 = Remote Keypad
(Also see PPN #28)
Relay: 1 = Relay #1
2 = Relay #2
3 = Set by entry code
Time Zone: 0 = no time zone
1-7 to restrict access per time zone 1-7
✦ NOTE: To have an entry code select which relay activates, the relay
option should be set to "3".
Defaults:
Key A "1" = Activates Relay #1
Key B "2" = Activates Relay #2
Key C "9" = Disconnect Visitor's Call
Keys ABCD
Defaults:
Programming = "###"
Command = "##"
Command
Default 2: Seconds
Time
Default: 2 Seconds
Time
Relay Time Zone