Napoleon HD81 Installation And Operating Instructions Manual
Napoleon river rock / stone burner assembly
Hide thumbs
Also See for HD81:
- Installation and operation instructions manual (12 pages) ,
- Installation and operating instructions manual (12 pages) ,
- Installation instructions manual (12 pages)
Table of Contents
Advertisement
Quick Links
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.
HD81
RIVER ROCK / STONE
BURNER ASSEMBLY
B81NS
NATURAL GAS
B81PS
PROPANE
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
SAFETY INFORMATION
WARNING
!
If the information in these instructions are
not followed exactly, a fi re or explosion
may result causing property damage,
personal injury or loss of life.
- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use
any phone in your building.
•
Immediately call your gas supplier from a
neighbour's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the
fi re department.
- Installation and service must be performed by a
qualifi ed installer, service agency or the supplier.
Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonfi replaces.com • ask@napoleonproducts.com
$10.00
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
INSTALLATION AND
1.22
W415-0808 / A / 11.09.10
1
Advertisement
Chapters
Table of Contents
Related Manuals for Napoleon HD81
Summary of Contents for Napoleon HD81
-
Page 1: Burner Assembly
- Installation and service must be performed by a qualifi ed installer, service agency or the supplier. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030 Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonfi replaces.com • ask@napoleonproducts.com $10.00... -
Page 2: Table Of Contents
NOTE: Changes, other than editorial, are denoted by a line in the margin. 1.0 GENERAL INFORMATION This rock burner assembly is approved for use in the HD81 gas appliance only. It is not approved for use as a stand alone appliance or in conjunction with any other appliance. -
Page 3: Installation
Do not use open fl ame. TUBE After leak test has been performed re-install ORIFICE access panel with gasket. (If removed) NIGHT LIGHT™ INSTALLATION Your HD81 comes equipped with 2 “Night Lights™”. The lights have been pre- wired and are controlled from the remote control. -
Page 4: Porcelain Base Installation
PORCELAIN BASE INSTALLATION INSTALL IN THE FOLLOWING ORDER: Side porcelain panels or brick panels must be installed prior to porcelain base cover plates. For side porcelain panel installation see “PRP81 PORCELAIN REFLECTIVE RADIANT PANEL” leafl et and for brick panel installation see “GD844KT DECORATIVE BRICK PANEL - SANDSTONE”... -
Page 5: Rock Installation
ROCK INSTALLATION WARNING REAL ROCKS MUST NOT BE USED IN THIS APPLIANCE. HEAT WILL CAUSE THEM TO EXPLODE. Position the two rock clusters in front of the Place the large cut out rocks along the edge center burner tube, ensuring the clusters are of the burner, making sure not to cover any sitting fl... -
Page 6: Adjustment
3.0 ADJUSTMENT FLAME CHARACTERISTICS It’s important to periodically perform a visual check of the pilot and burner fl ames. Compare them to the illustra- tions provided. If any fl ames appear abnormal call a service person. 3/8” - 1/2” PILOT BURNER ELECTRODE FLAME... -
Page 7: Replacements
4.0 REPLACEMENTS Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Authorized dealer / distributor. FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM. - Page 8 5.0 NOTES 44.1 W415-0808 / A / 11.09.10...
- Page 9 - Installation and service must be performed by a qualifi ed installer, service agency or the supplier. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030 Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonfi replaces.com • ask@napoleonproducts.com $10.00...
-
Page 10: General Information
NOTE: Changes, other than editorial, are denoted by a line in the margin. 1.0 GENERAL INFORMATION This burner and log assembly are approved for use in the HD81 gas appliance only. They are not approved for use as a stand alone appliance or in conjunction with any other appliance. -
Page 11: Bulkheads
BULKHEADS NOTE: Bulkhead covers need to be removed. Connect the gas fl ex lines and the pilot line Green to the gas bulkheads located under the valve Dots access opening. Be sure to match up the gas manifold marked with a green dot with the center bulkhead, also marked with a green dot. -
Page 12: Night Light™ Installation
NIGHT LIGHT™ INSTALLATION Your HD81 comes equipped with 2 “Night Lights™”. The lights have been pre-wired and are controlled from the remote control. Included with the burner assembly are the frames, lenses and gaskets that need to be installed as shown. -
Page 13: Log Placement
LOG PLACEMENT Place the left middle log #1 onto the Slide log #2 from right to left on the locating stud on the middle log support. middle log support creating a tight fi t Make sure the hollow on the underside between logs #1 and #2. -
Page 14: Charcoal Lumps
Place the pin in log #8 into the locating Slide the fl at portion of log #7 under the hole on log #1 and rest the bottom of second grate post. the log on log #5. NOTE: Logs 3, 4, 5, 6 and 7 are included twice. -
Page 15: Vermiculite
VERMICULITE Sprinkle vermiculite around the charcoal embers. NOTE: Vermiculite is not to be placed on the burner. 33.1 2.10 GLOWING EMBERS Tear the embers into pieces and place along the front row of ports covering all of the burner area. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the fi... - Page 16 4.0 REPLACEMENTS Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Authorized dealer / distributor. FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.
- Page 17 W415-0713 / A / 11.09.10...
- Page 18 5.0 NOTES 44.1 W415-0713 / A / 11.09.10...
- Page 19 44.1 W415-0713 / A / 11.09.10...
- Page 20 44.1 W415-0713 / A / 11.09.10...
- Page 21 - Installation and service must be performed by a qualifi ed installer, service agency or the supplier. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030 Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonfi replaces.com • ask@napoleonproducts.com $10.00...
- Page 22 NOTE: Changes, other than editorial, are denoted by a line in the margin. 1.0 GENERAL INFORMATION This glass burner assembly is approved for use in the HD81 gas appliance only. It is not approved for use as a stand alone appliance or in conjunction with any other appliance.
-
Page 23: Bulkheads
BULKHEADS NOTE: Bulkhead covers need to be removed. Green Connect the gas fl ex lines and the pilot line Dots to the gas bulkheads located under the valve access opening. Be sure to match up the gas manifold marked with a green dot with the center bulkhead, also marked with a green dot. -
Page 24: Night Light™ Installation
NIGHT LIGHT™ INSTALLATION Your HD81 comes equipped with 2 “Night Lights™”. The lights have been pre-wired and are controlled from the remote control. Included with the burner assembly are the frames, lenses and gaskets that need to be installed as illustrated. -
Page 25: Glass Media
Align the 4 tabs on the porcelain base down to line up with the holes in the burner tray. Secure using the screws provided. Bend Tabs GLASS MEDIA WARNING CLEAN THE GLASS MEDIA PRIOR TO INSTALLATION. BEFORE APPLYING THE CLEANED GLASS, ENSURE THAT IT IS DRY. -
Page 26: Adjustment
3.0 ADJUSTMENT FLAME CHARACTERISTICS It’s important to periodically perform a visual check of the pilot and burner fl ames. Compare them to the illustra- tions provided. If any fl ames appear abnormal call a service person. 3/8” - 1/2” PILOT BURNER ELECTRODE FLAME... -
Page 27: Replacements
4.0 REPLACEMENTS Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Authorized dealer / distributor. FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM. - Page 28 5.0 NOTES 44.1 W415-0712 / A / 11.09.10...