Surround And Cast Trim Set - Quadra-Fire CASTILEI-MBK Installation Manual

H. Surround and Cast Trim Set
I ncluded in Surround Kit: (2) side surrounds, left and right;
(1) surround top; (1) fastener package.
Included in Cast Trim Kit: (2) cast trim legs, left and right; (1)
cast trim header; (2) cast trim footers, left and right
Tools Needed: 4-6 inch long Philips head screwdriver, pliers
and fl at head screwdriver.
1. Place the peel and stick round felt vibration insulation
pads on the front side in each corner of the top metal
piece and on the back side in each corner of the top cast
piece. Figure 23.1
2. Lay surround face down on a fl at protected surface to
prevent scratching.
3. Using the Philips screwdriver attach the side surrounds
to the top surround using 2 sheet metal screws provided
with the kit on each side.
4. Assemble Cast Trim and attach to surround:
a) Place corresponding cast trim pieces (2 cast trim sides
and 1 cast trim header) underneath the surround set, also
face down. Align the holes in the metal pieces with the 5
bosses on the top cast piece and 2 bosses on each side
piece. Figure. 23.1
b) Attach the magnets to the magnet brackets with one
countersink screw each. Attach magnet and bracket to
the metal surround sides with magnet facing the front as
shown in Figure. 23.1.
c) Place cast footers under metal sides aligning the top and
bottom holes.
d) The 9 mounting clips are shipped in one long strip. Use
your hands or pliers to break them apart.
e) Each clip has a clearance notch to allow room for the
cast on the boss. Place the clips over the boss so that
the notch is facing the outer edge of the surround. Figure
23.3
f) It is best to install all of the 1/4-20 screws only half way
at fi rst to allow for adjustments. After adjustment tighten
the 2 screws in each footer fi rst and then work your way
around to the rest.
5. Remove the cast sides before attaching the surround
and trim. Lift up the top to expose the thumb screws that
secure the cast sides. Remove the thumb screw and top
bracket and then remove the cast side. NOTE: The right
cast side bracket has the hopper cut out switch attached.
Remove the retainer from the right side and allow to
hang down into the insert or disconnect the switch when
removing side.
6. Install the power cord in the surround.
7. If power enters the appliance on the right side: Using the
pliers, attach cord restraint 12 inches from the female end
of the cord and then press into the right side panel.
July 7, 2015
8. If power enters appliance on the left side: The cord will
have to be routed through the back of the insert. When
routing the power cord, keep cord lying fl at as possible,
keeping the cord away from all exhaust surfaces and
moving parts. After routing, install cord restraint and
press into the left side panel.
9. Slide surround over the top of the insert into place. Sur-
round attaches to bottom and top of insert sides with the
supplies 1/4 inch screws.
10. Plug cord into inlet on junction box routing the wire.
11. Install plug into unused hole.
(4) Felt Vibration Insulation Pads
Secure
Surrounds to
Cast Trim Kit
Attach Magnet
before installing
Cast Footers
Magnet Installed
Figure 23.1
Back
of
Side
Piece
Magnet Attached - Faces Front
Figure 23.2
Surround Set
attaches to top
and bottom of
insert sides.
Figure 23.4
7022-514C
CASTILE INSERT
Cast Footers,
Left & Right
Clearance Notch
Figure 23.3
Thumb
Screw
Bracket
23