Lincoln Electric RANGER IM511-D Operator's Manual page 34

RANGER 9 / LN-7 CONNECTION DIAGRAM
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
Do not touch electrically live parts.
14 PIN
AMPHENOL
6 PIN
TO WORK
AMPHENOL
CAUTION :
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
THE ENGINE WELDER OPERATING MANUAL.
N.A. USE POLARITY SWITCH TO SET FOR DESIRED ELECTRODE POLARITY. POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.
PLACE WELDING TERMINALS SWITCH TO "REMOTELY CONTROLLED" POSITION.
N.B. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE
APPLICATIONS. SEE OPERATING MANUAL.
N.C. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED, PLACE OUTPUT CONTROL SWITCH IN "OUTPUT CONTROL REMOTE" POSITIION.
N.D. PLACE IDLER SWITCH IN "HIGH" IDLE POSITION.
RANGER 9 TO K867 ADAPTER CONNECTION DIAGRAM
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
Do not touch electrically live parts.
14 PIN
AMPHENOL
K867 UNIVERSAL
ADAPTER PLUG
ELECTRODE
TO WORK
ELECTRODE CABLE
TO WIRE FEED UNIT
TO WORK
CAUTION :
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
THE ENGINE WELDER OPERATING MANUAL.
N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.
N.B. USE POLARITY SWITCH TO SET DESIRED POLARITY, POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.
N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.D. FOR WIRE FEEDERS THAT RETURN A SIGNAL FOR WELDING OUTPUT, USE ISOLATION
RELAY TO CLOSE LEADS 2 & 4.
N.E. REFER TO POWER SOURCE INSTRUCTION MANUAL FOR MAXIMUM AUXILIARY CURRENT DRAW.
WARNING
TO LN-7 INPUT
CABLE PLUG
ELECTRODE
TO WORK
WARNING
81
82
SPARE
2
4
41
42
31
32
GND
21
77
76
75
– 32 –
Keep guards in place.
Keep away from moving parts.
Only qualified personnel should install,use
or service this equipment.
K584-XX INPUT CABLE ASSEMBLY
ELECTRODE CABLE
TO WIRE FEED UNIT
Keep guards in place.
Keep away from moving parts.
Only qualified personnel should install,use
or service this equipment.
NOT USED ON RANGER POWER SOURCES
CONNECT TOGETHER FOR
WELDING OUTPUT
42 VAC
N.E.
115 VAC
POWER SOURCE FRAME CONNECTION
WIRE FEEDER VOLTMETER CONNECTION
CONNECTS TO (WORK TERMINAL) OF POWER SOURCE
10K
REMOTE OUTPUT CONTROL
MIN.
{
2
TO
K867
4
OPTIONAL K857
REMOTE CONTROL
1 2 - 1 6 - 9 3
M 1 7 0 9 2
N.C.
N.D.
TO
WIRE
FEEDER
1 2 - 1 6 - 9 3
M 1 7 0 9 3