Canon i-SENSYS MF4300dn Service Manual page 150

Chapter 13
Error Code Description
0016 Receive DCN signal after sending PTT signal.
0017 Can't receive any response from remote side after sending DIS
0018 Can't detect energy within 6 sec after sending FTT command
0019 Received DCN signal sending CFR signal
001A No energy on line over 6 sec. within phase C before any corrected ECM frame.
001D Can't detect flag after sending CFR signal
001E Timeout in V.17 ECM Rx phase C
0020 Can't correct frame within 6 sec at phase C.
0021 File full.
0022 Owing to noise interference on the line, receiving side can't receive correct data within specified time (no ECM)
0023 Can't receive correct signal after sending CFR signal
0030 Can't receive any signal within 6 sec. At phase D.
0031 Received incorrect signal at phase D (not EOP, MPS, EOM, DCN, PPS_Q, PPS_Q,etc)
0032 Can't receive carrier within 6 sec after sending MCF or RTP, RTN signal
0033 Received DCN signal at ohase D within pages (not last page).
0039 In non_ECM mode, when machine alredy received the data dosen't receive 13.1 seconds
001F Can't detect any G3 signal within 35 sec after sending DTC signal
003F Remote side TSI not define in machine one touch or speed dial directory
0040 Can't receive carrier within 6 sec. after sending CTR.
0041 Can't receive carrier within 6 sec. after sending PPR.
0042 Can't receive correct signal after sending RNR signal
0043 Receive incorrect signal at phase D in ECM mode.
0044 Can't receive carrier/FSK signal within 6 sec. After sending MCF. ln ECM mode.
0047 Can't receive correct signal or DCN received after sending ERR signal.
0048 Can't receive correct signal after receive PPS_PRI_Q
004B Can't detect correct FSK signal even through detected FSK tone within 6 sec.
004C Handshake fail during re-train or between page in V34 Rx.
004E Receive DCN signal after sending DIS in V.34.
004F Remote side disconnected after sending ANSam in V.8 phase.
0050 Can't receive any correct signal after detected CJ signal in V.8 phase.
0051 Can't receive phase 3 signal after phase 2 within 20 seconds in V.34.
0053 Modem disconnect after phase 4 in V.34.
0054 Remote side disconnect after phase 4 in V.8
0055 Receive incorrect signal after sending DIS signal in V.34
0056 Modem disconnect after sending CFR in V.34
0058 Can't detect image signal within 6 sec after modem enter to primary phase in V.34
005A Modem cannot detect any correct ECM frame with 3 minutes in phase C.
005B Modem can't detect control channel with 12 sec in phase C
005C Detect busy tone within control channel after phase C.
005D Modem can't detect any correct ECM frame with 12 sec in phase C.
005E Can't detect control channel signal after received RCP frame within 6 sec
005F Can't detect silence after sending JM signal for polling TX function.
0060 There are no any bullietin files to be polled in V.34.
0061 Machine cannot detect V.21 or V.8 signal with 35 sec.
0062 Modem disconnect in phase D after our side sending out flags sequence in control channel.
0063 Can't receive any flag sequence in control channel within 25 sec in phase D.
0064 Can't detect any control channel signal in phase D within 60 sec even through energy still on the line.
0065 Can't detect any control channel signal within 60 sec after detect sillence in phase D.
0066 Can't receive T.30 signal or carrier after sending CFR in V.34.
13-2