Vision Fitness R40 Owner's Manual page 11

R20 assEmBlY STEP 3
LEAD WIRE
CONSOLE CABLES
R20
SPRING WASHERS (C)
HANDLEBAR
SET SCREW (H)
CONSOLE CABLES
CONSOLE MAST
CONSOLE MAST GROMMET
SPRING WASHERS (C)
RIGHT PEDAL
RIGHT CRANK ARM
20
HARDwARE fOR STEP 3 :
BOLTS (A) SPRING
BOLT (D) BOLT (A)
WASHER (C)
15 mm 20 mm
15.4 mm
Qty: 4 Qty: 2
Qty: 6
a open hardware for step 3.
B slide the console mast grommet from the bottom up the
console mast.
C attach the console cables from the bike frame to the lead
wire in the bottom of the console mast and carefully pull the lead
wire through the console mast until the console cables are
located at the top of the mast.
d slide the console mast onto the bike frame. detach and discard
the lead wire.
E attach the mast to the frame with 4 bolts (d), 4 spring washers
BOLTS (D)
(c) and 1 set screw (h) and slide the console mast gRommET
down over the bike frame.
F attach the console handlebar to the console mast using 2
bolts (a) and 2 spring washers (c).
g attach the pedal strap to the right pedal. attach the right
pedal to the right crank arm, tightening it clockwise with the
provided 15mm/17mm flat wrench.
H attach the pedal strap to the left pedal. attach the left pedal
onto the left crank arm, tightening it counter-clockwise
with the provided 15mm/17mm flat wrench. (noTE: The left crank arm
is reverse-threaded so it is very important that it is tightened counter-
clockwise. Tightening it the opposite way can damage the pedal or the
crank arm or both.)
R40 assEmBlY STEP 3
LEAD WIRE
CONSOLE CABLES
SET SCREW (H)
10 mm
Qty: 1
CONSOLE MAST
CONSOLE MAST GROMMET
HARDwARE fOR STEP 3 :
BOLTS (D)
SPRING
BOLT (H)
WASHER (C)
15 mm
15.4 mm
SPRING WASHERS (C)
Qty: 4
Qty: 6
HANDLEBAR
a open hardware for step 3.
SET SCREW (I)
B slide the console mast grommet from the bottom up the
CONSOLE CABLES console mast.
C attach the console cables from the bike frame to the lead
wire in the bottom of the console mast and carefully pull the lead
wire through the console mast until the console cables are
located at the top of the mast.
d Carefully tuck all cables into the bike frame and slide the console
mast onto the bike frame. detach and discard the lead wire.
SPRING WASHERS (C)
E attach the mast to the frame with 4 bolts (d), 4 spring washers
BOLTS (H)
(c) and 1 set screw (h) and slide the console mast grommet
down over the bike frame.
F attach the console handlebar to the console mast using 2
bolts (d) and 2 spring washers (c).
g attach the pedal strap to the right pedal. attach the right
pedal to the right crank arm, tightening it clockwise with the
provided 15mm/17mm flat wrench.
RIGHT PEDAL
H attach the pedal strap to the left pedal. attach the left pedal
onto the left crank arm, tightening it counter-clockwise
RIGHT CRANK ARM
with the provided 15mm/17mm flat wrench. (noTE: The left crank
arm is reverse-threaded so it is very important that it is tightened
counterclockwise. Tightening it the opposite way can damage the pedal
or the crank arm or both.)
BOLT (D) SET SCREW (I)
R40
20 mm 10 mm
Qty: 2 Qty: 1
21