Advertisement
CArE & CLEAnIng
PAge heAder.....
CLEAnIng tHE SHoWEr SCrEEn
•
The group head interior and shower
screen should be wiped with a damp cloth
to remove any ground coffee particles.
•
Periodically run hot water through the
machine with the filter basket and
portafilter in place, without ground
coffee, to rinse any residual coffee.
CLEAnIng tHE drIP trAy
& StorAgE trAy
•
The drip tray should be removed,
emptied and cleaned after each use or
when the drip tray indicator is showing
Empty Me!
•
Remove grill from the drip tray. Wash
the drip tray in warm soapy water.
The Empty Me! indicator can also be
removed from the drip tray.
•
The storage tray can be removed and
cleaned with a soft, damp cloth (do not
use abrasive cleansers, pads or cloths
which can scratch the surface).
CLEAnIng tHE oUtEr HoUSIng
& CUP WArmIng trAy
•
The outer housing and cup warming tray
can be cleaned with a soft, damp cloth.
Polish with a soft, dry cloth. Do not use
abrasive cleansers, pads or cloths which
can scratch the surface.
notE
Do not clean any of the parts or
accessories in the dishwasher.
dESCALE (dESc):
Use this function to access the step by step
de-scale procedure. The current step will be
displayed on the GRIND LCD.
33
CAUTION
Never open DESCALE ACCESS valves
while machine is still hot. Allow
machine to cool for 1 hour prior to
starting de-scale process.
CAUTION
During de-scale process, water may
flow through group head at any time.
Step 1 – Prepare for de-scale
With the machine OFF, press &
j)
hold the 1 CUP button, then press the
POWER button until advanced menu
is displayed.
Rotate SELECT dial to dESc then push
k)
SELECT dial.
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
TEMP TEXTURE
TEMP TEXTURE
TEMP TEXTURE
TEMP TEXTURE
TEMP TEXTURE
TEMP TEXTURE
Empty water tank, remove
l)
water filter then fill water tank
with de-scale solution, as per
manufacturer's instructions.
Fill tank with water to MAX line. Fill
m)
tank with water to MAX line and reinsert
tank into machine.
Ensure drip tray is empty and
n)
installed into position. Place a cloth on
the right side of the drip tray to stop
steam escaping.
CArE & CLEAnIng
PAge heAder.....
Step 2 – Empty Boilers
The GRIND LCD will display 02 during
Step 2 procedure.
Remove grey silicon cover on the
a)
right hand lower side of the front
panel marked DESCALE ACCESS.
Place a cloth over the drip tray to stop
steam escaping.
REMOVE
Using a flat-head screwdriver, rotate the
b)
left screw counter-clockwise first, until
valve is fully open. Water will begin to
flow into drip tray from underneath.
Do the same for the right screw.
c)
Steam will be released from the boiler.
CAUTION HOT WATER
CAUTION HOT STEAM
Close valves when water stops flowing
d)
through both outlets. Empty drip tray
and re-assemble onto unit.
CAUTION HOT WATER
Push SELECT button, to proceed to
e)
next step.
notE
If boilers are not empty, the machine
will beep 3 times and the downlights
will flash 5 times and "VALV" will be
displayed in the LCD.
Step 3 – Begin de-scale
The GRIND LCD will display 03 during
Step 3 procedure.
notE
If water tank has not been removed
then replaced or is empty, water tank
LED will flash 5 times and the machine
will beep 3 times and "Fill Tank" will
be displayed in the LCD.
Machine will fill boilers with de-scale
a)
solution and heat to temperature.
20 minute timer will begin. Wait for
b)
countdown timer to get to 0:00.
(This allows solution to dissolve scale
build up).
34
Advertisement
