Summary of Contents for Ariens 911110 - P 21LM, 911112 - DSP 21LM, 911111 - SP 21LM, 911113 - DESP21LM
Page 1
Walk Behind Lawn Mower Owner/Operator Manual Transfer Coller l’autocollant du model & modèle et du numéro de serial number série dans cet encadré. label from Transferir aquí la etiqueta product del modelo y número de registration serie del registro del here.
INTRODUCTION • Record Engine Model & Serial numbers here: PRODUCT REGISTRATION The Ariens dealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information. All claims meeting...
HAZARDOUS SITUATION! If not avoided, WILL RESULT in death or serious injury. DISCLAIMER Ariens reserves the right to discontinue, make changes to, and add improvements upon its products at any time without public notice or obligation.The descriptions and specifications contained in this manual were in effect at printing.
SAFETY DECALS AND LOCATIONS ALWAYS replace missing or damaged safety decals. Refer to Figure 2 for safety decal locations. Figure 2 1. DANGER! TO AVOID SERIOUS INJURY OR DEATH Read the operator’s manual. OL1801 Keep children and others away from unit while operating. OL4370 Never direct discharge toward other people.
Page 5
If the operator or the mechanic cannot read the manual, it is the owner’s responsibility to explain it to them. Only the user can prevent and is responsible for accidents or injuries occurring to themselves, other people or property. ALWAYS remove key (if equipped) and disconnect wire from spark plug before assembly.
Page 6
A spark arrestor, if used, must be maintained in effective working order by the operator. See your Ariens Dealer or engine manufacturer’s service center. Fuel is highly flammable and its vapors can explode.
Page 7
DO NOT store unit inside a building with fuel in the fuel tank where any ignition sources are present. Use only accessories which have been approved by Ariens and are properly installed. Use only accessories or attachments that are designed for your unit and that can be used safely on your terrain.
CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding. CARTON CONTENTS 1. Mower Unit 2. Mulch Cover 3. Side Discharge Chute 4. Mulch Plug 5. Literature Pack 6. Grass Bag Figure 3 ASSEMBLY ASSEMBLY 1. Remove mower and handlebar from carton.
Page 9
6. Connect the engine/blade control cable to the engine. Route the z-bend cable end into engine shutoff lever as shown below. Insert the cable connector into the cable mounting bracket on the engine. Make sure the connector snaps into place securely.
CONTROLS AND FEATURES 1. Engine/Blade Control (911110, 111) 2. Wheel Drive Control (911111) 3. Handlebars 4. Grass Bag 5. Rear Door 6. Fuel Tank and Cap 7. Oil Fill/Dipstick 8. Muffler and Muffler Guard 9. Cutting Height Levers (2 Rear Wheel Adjusters, 2 Front Wheel Adjusters) 10.
CONTROLS AND FEATURES See Figure 6 for locations. WARNING: Improper operation can lead to injury. Learn what the controls do and how they work. Thoroughly read and understand entire Operator Manual. CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding.
Page 12
Cutting Height Settings Chart Notch Cut grass length 1" (25 mm) 1-1/4" (32 mm) 1-1/2" (38 mm) 2-1/4" (57 mm) 2-3/4" (70 mm) 3-1/2" (89 mm) 4" (102 mm) Standard Models To change cutting height, move cutting height levers one notch at a time on each wheel to set desired height (Figure 7).
911112, 113 To drive forward: Slowly pull the wheel drive control toward you until you reach a comfortable ground speed. Hold the wheel drive control in this position to maintain the speed. To stop: Release wheel drive control. Figure 9 Speed Limiter (911111, 112, 113) The speed limiter increases or decreases tension in the drive cable, which limits the...
Page 14
To Bag (Optional on Push Models) CAUTION: Check grass bag frequently for wear or deterioration. Replace worn or damaged bag with Ariens original equipment replacement bag only. See Figure 11 on page 14. 1. Shut off unit. 2. Make sure mulch cover is closed and secured with knob.
1. Side Discharge Chute 2. Knob Figure 12 To Mulch See Figure 13 on page 15. 1. Shut off unit. 2. Remove grass bag and side discharge chute, if installed. 3. Make sure mulch cover is closed and secured with knob. 4.
Page 16
STARTING AND SHUT OFF WARNING: Improper operation can lead to injury. Learn what the controls do and how they work. Thoroughly read and understand entire Operator Manual. See Figure 6 for all Controls and Features. NOTE: Start engine on a level surface that is free of debris.
CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding. Ariens Dealers will provide any service, parts or adjustments which may be required to keep your unit operating at peak efficiency. Should engine require service, contact an Ariens Dealer or an authorized engine manufacturer's service center.
GENERAL LUBRICATION NOTE: The mower transmission is lubricated and sealed at the factory. It should need no routine lubrication. If the transmission leaks grease, bring the mower to your local Ariens dealer for repair. GB - 18 Blade Figure 15...
CHECK SPARK PLUG Spark plug should be replaced every 100 hours of operation or each year. NOTE: Loose spark plug wire terminals can cause sparking. Replace terminal if damaged. CHECK ENGINE COOLING WARNING: HOT SURFACES can cause death or serious injury. DO NOT TOUCH parts which are hot from operation.
DRIVE BELT REPLACEMENT (self-propelled models) To remove drive belt: 1. Disconnect spark plug wire from spark plug. 2. Remove transmission cover. 3. Disconnect idler return spring from idler arm. See Figure 17. 4. Disconnect the wheel drive cable from transmission mount, and then disconnect drive cable spring from idler arm.
NOTE: The engine/blade control has no user serviceable adjustments. If the engine/blade control does not stop the engine or blade within 3 seconds of releasing the control bail, take the unit to an authorized Ariens dealer for repairs. BATTERY (electric start models) WARNING: AVOID INJURY.
Figure 22 WHEEL DRIVE CONTROL ADJUSTMENT (self-propelled models) See Figure 23. NOTE: The unit should stop immediately when the wheel drive control is released, and the unit should not creep forward when the wheel drive control is disengaged with the engine running.
Brush off dirt and debris from all surfaces. Touch up all scratched surfaces to prevent rust. Matching touch-up paint is available from your Ariens Dealer. Do not use abrasives, solvents, or harsh cleaners. PROBLEM...
5. Bearings damaged. 6. Debris in gear set. 7. Drive seems to slip or speed is too slow. SERVICE PARTS Always use genuine Ariens parts to keep your mower running like new. Description Part Number Air Filter 21529800 (911110, 111)
Model Number Description Length - in. (cm) Height - in. (cm) Width - in. (cm) Actual Weight - lbs (kg) Cutting Width- in. (cm) Cutting Height - in. (cm) Engine, 4 cycle Model Trim Engine Power - HP (kW) @ Max. RPM Max Rotation Speed of Cutting Edge - RPM (min...
Page 26
(90) days after the date of purchase or 1000 hours of use, whichever comes first, if any product is rented or leased. Ariens Company • 655 W. Ryan St, P.O. Box 157 • Brillion, WI 54110-0157• (920) 756-2141 • www.ariens.com Ariens Limited...
(12) months after the date of purchase. Ariens may from time to time change the design of its products. Nothing contained in this warranty shall be construed as obligating Ariens to incorporate such design changes into previously manufactured products, nor shall such changes be construed as an admission that previous designs were defective.
Page 28
Ariens Company 655 West Ryan Street P.O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www.ariens.com...