Cisco 6500 Series Software Configuration Manual page 85

Chapter 6 Configuring Interfaces
With releases earlier than Release 12.1(26)E, for VLAN interfaces, the interface range command
•
supports only those VLAN interfaces for which Layer 2 VLANs have been created with the
interface vlan command (the show running-configuration command displays the configured
VLAN interfaces). The interface range command does not support VLAN interfaces that are not
displayed by the show running-configuration command.
With Release 12.1(26)E and later releases, the interface range command supports VLAN interfaces
•
for which Layer 2 VLANs have not been created with the interface vlan command.
With releases earlier than Release 12.1(14)E, you cannot use the interface range command to create
•
VLAN interfaces: the interface range command is supported only to modify VLAN interfaces that
have been created with the interface vlan command. You can enter the show
running-configuration command to display the configured VLAN interfaces.
The link state messages (LINK-3-UPDOWN and LINEPROTO-5-UPDOWN) are disabled by default.
Note
Enter the logging event link status command on each interface where you want the messages enabled.
This example shows how to reenable all Fast Ethernet ports 5/1 to 5/5:
Router(config)# interface range fastethernet 5/1 - 5
Router(config-if)# no shutdown
Router(config-if)#
*Oct
*Oct
*Oct
*Oct
*Oct
*Oct
5, changed state to up
*Oct
3, changed state to up
*Oct
4, changed state to up
Router(config-if)#
This example shows how to use a comma to add different interface type strings to the range to reenable
all Fast Ethernet ports in the range 5/1 to 5/5 and both Gigabit Ethernet ports (1/1 and 1/2):
Router(config-if)# interface range fastethernet 5/1 - 5, gigabitethernet 1/1 - 2
Router(config-if)# no shutdown
Router(config-if)#
*Oct
*Oct
*Oct
*Oct
*Oct
*Oct
up
*Oct
up
*Oct
5, changed state to up
*Oct
3, changed state to up
*Oct
4, changed state to up
Router(config-if)#
78-14099-04
6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet5/1, changed state to up
6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet5/2, changed state to up
6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet5/3, changed state to up
6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet5/4, changed state to up
6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet5/5, changed state to up
6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet5/
6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet5/
6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet5/
6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet5/1, changed state to up
6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet5/2, changed state to up
6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet5/3, changed state to up
6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet5/4, changed state to up
6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet5/5, changed state to up
6 08:29:28: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to
6 08:29:28: %LINK-3-UPDOWN: Interface GigabitEthernet1/2, changed state to
6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet5/
6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet5/
6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet5/
Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide—Release 12.1 E
Configuring a Range of Interfaces
6-5