Table of Contents
Advertisement
6.13 Display messages
A series of messages in addition to those already found in
the previous paragraphs, can be shown on the machine's
display (ref. 8a,fig. 1).
STANDBY: it appears when the machine is off (with main
switch in position "I") with the function of automatic switching
on / switching off enabled (see "6.14 Menu-programmable
functions").
ANTIFREEZING: it is displayed when the machine is off (with
main switch in position " I ") and the program preserving the
icing
up
of
boilers
is
programmable functions").
RINSING PROGRAMMED
:
automatically washes the coffee dispenser (see "6.14 Menu-
programmable functions").
ADD COFFEE: it is displayed when during a grinding phase
the machine detects no coffee beans inside the hopper (ref.
7, fig.1).
LOAD THE CIRCUIT: it appears when the machine, during
the dispensing of any drink, detects that water is missing
from the boilers.
After having checked the direct water supply, press button
(
for the COFFEE version) until the water flows regularly
from the water dispensing tube (ref.11, fig.1) and the coffee
dispenser (ref.24, fig.1). In the COFFEE version wafer only
flows from the coffee dispensing unit.
PROGRAMMING: it is displayed when machine
programming is accessed (see "6.14 Menu-programmable
functions").
EMPTY GROUNDS: it is displayed when the grounds tray
(ref. 17, fig. 1) is almost full (the machine has completed the
programmed number of dispensing instances). Other further
dispensing Instances can be carried out.
OUT OF SERVICE - EMPTY GROUNDS: it is displayed
when the grounds tray (ref. 17, fig. 1) is completely full (the
machine has supplied the programmed number of dispensing
instances).
The machine is locked and no further dispensing is possible
until the grounds tray has been emptied.
CLOSE SERVICE DOOR:
(ref. 13, fig. 1) is not properly closed.
INSERT GROUNDS DRAW. : it is shown when the grounds
tray (ref. 17, fig. 1) is not correctly positioned.
INSERT DRIP TRAY: displayed when the drip tray (ref. 15,
fig. 1 j is not correctly positioned.
INSERT BREWING UNIT: displayed when the brewing unit
(ref. 25, fig. 1) is not correctly positioned.
:
BREWING UNIT ERROR
(ref. 25, fig. 1) incorrectly performs its working cycle; switch
machine off and call the AUTHORISED SERVICE CENTRE.
activated
(see
"6.14
Menu-
it is displayed when the machine
displayed when the front door
displayed when the brewing unit
SENSOR ERROR 01: displayed when a temperature sensor
is out of order. Switch machine off and call the AUTHORISED
SERVICE CENTRE.
TEMPER. ERROR 01: displayed when one of the boiler
heating elements is out of order. Switch machine off and call
the AUTHORISED SERVICE CENTRE.
DESCALING: it is displayed when the machine requires this
type of intervention, having carried out the programmed
number of dispensing instances. Switch machine off and call
the AUTHORISED SERVICE CENTRE.
The descaling interventions depend on the machines' work
cycles programmable by the maintenance technician.
MAINTENANCE: it is displayed when the machine requires
maintenance having performed the programmed number of
dispensing instances. Switch machine off and call the
AUTHORISED SERVICE CENTRE.
Maintenance interventions are based on the machine's
working
cycles,
programmable
technician.
6.14 Menu-programmable functions
The machine can be set by programming the menu; these
modifications match the product dispensed to User
requirements.
Important
During the programming phase several keys assume a
different function from that applicable during normal
use and permit:
(access to
access to the programming menu by
programming)
keeping the key pressed for 5 sees. (the
display will show "
(Enter)
passing from a menu level to the next;
preparing a datum to be modified;
confirming a datum or a function;
(Escape)
canceling unconfirmed modifications;
stepping back to the previous menu level
until quitting.
(Down)
passing to the next item within the same
programming level;
Increasing the value of a datum to be
modified.
(Up)
switching to the previous item within the
same programming level;
reducing the value of the datum to be
modified.
Several functions also foresee the programming of one
or more data (already programmed for standard values).
In order to operate on the data values to be re-
programmed it is necessary to:
- Select function.
- Confirm function with key
English
by
the
maintenance
PROGRAMMING
");
(Enter)
13
Hide quick links:
Advertisement
Table of Contents
