Sony DCR-TRV30E Service Manual page 32

Dubbing only desired scenes
– Digital program editing
Notes
•You cannot dub the titles, display indicators, or
the contents of cassette memory.
•When you connect with an i.LINK cable (DV
connecting cable), you may not be able to
operate the dubbing function correctly,
depending on the VCR.
Set CONTROL to IR in the menu settings of
your camcorder .
•When editing digital video, the operation
signals cannot be sent with LANC .
If you connect using an i.LINK cable (DV
connecting cable)
With digital-to-digital connection, video and
audio signals are transmitted in digital form for
high-quality editing.
94
Dubbing only desired scenes
– Digital program editing
1
VCR
OFF(CHG)
CAMERA
3
MEMORY
MENU
4
O T H E R S
D A T A COD E D A T E / C AM
B E E P
– – – – – – – –
COMMA ND E R
D I S P L A Y – –:– –:– –
V I D EO E D I T
E D I T S E T – – – – –
R E T URN
– – – – – –
– – – – – –
[ ME NU ] : E ND
5
O T H E R S
E D I T S E T
CON T RO L I R
A D J T E S T
" CU T - I N "
" CU T -OU T "
I R S E T U P
P A U S EMOD E
I R T E S T
R E T URN
[ ME NU ] : E ND
96
6-9
O T H E R S
O T H E R S
E D I T S E T
E D I T S E T
CON T RO L I R
CON T RO L I R
A D J T E S T
A D J T E S T i L I N K .
" CU T - I N " " CU T - I N "
" CU T -OU T " " CU T -OU T "
I R S E T U P I R S E T U P
P A U S EMOD E P A U S EMOD E
I R T E S T I R T E S T
R E T URN
R E T URN
[ ME NU ] : E ND [ ME NU ] : E ND
O T H E R S
O T H E R S
E D I T S E T
E D I T S E T
CON T RO L CON T RO L
A D J T E S T A D J T E S T
" CU T - I N " " CU T - I N "
" CU T -OU T " " CU T -OU T "
I R S E T U P 3 I R S E T U P 4
P A U S EMOD E P A U S EMOD E
I R T E S T I R T E S T
R E T URN
R E T URN
[ ME NU ] : E ND [ ME NU ] : E ND
Dubbing only desired scenes
– Digital program editing
Step 2: Setting the VCR to
operate with the A/V
connecting cable
To edit using the VCR, send the control signal by
infrared rays to the remote sensor on the VCR.
When you connect using an A/V connecting
cable, follow the procedures below, (1) to (4), to
send the control signal correctly.
(1) Set the IR SETUP code
1 Set the POWER switch to VCR on your
camcorder.
2 Turn the power of the connected VCR on,
then set the input selector to LINE.
When you connect a video camera recorder,
set its power switch to VCR/VTR.
3 Press MENU to display the menu.
4 Turn the SEL/PUSH EXEC dial to select
then press the dial.
5 Turn the SEL/PUSH EXEC dial to select EDIT
SET, then press the dial.
6 Turn the SEL/PUSH EXEC dial to select
CONTROL, then press the dial.
7 Turn the SEL/PUSH EXEC dial to select IR,
then press the dial.
8 Turn the SEL/PUSH EXEC dial to select IR
SETUP, then press the dial.
9 Turn the SEL/PUSH EXEC dial to select the
IR SETUP code of your VCR, then press the
dial.
Check the code in "About the IR SETUP
code." (p. 97)
Dubbing only desired scenes
– Digital program editing
About the IR SETUP code
The IR SETUP code is stored in the memory of
your camcorder. Be sure to set the correct code
depending on your VCR. The default setting is
Code number 3.
IR SETUP code/
Brand/
Sony 1, 2, 3, 4, 5, 6
Aiwa 47, 53, 54
Akai 62, 50, 74
Alba 73
Aristona 84
Baird 36, 30
Blaupunkt 83, 78
Bush 74
Canon 97
CGM 47, 83, 36
Clatronic 73
Daewoo 26
Ferguson 76
Fisher 73
Funai 80
Goldstar 47
Goodmans 26, 84
Grundig 83, 9
Hitachi 42, 56
ITT/Nokia Instant 36
JVC 12, 21, 15, 11
Kendo 47
Loewe 16, 47, 84
Luxor 89
Mark 26*
Matui 47, 60, 58*
Mitsubishi 28, 29
* TV/VCR component/
Note on IR SETUP code
Digital programme editing is not possible if the
VCR does not support IR SETUP codes.
1-22
(1) (4)
(1)
1
2
,
3
4
5
6
7
8
9
IR SETUP code/
Brand/
Nokia 89, 36
Nokia Oceanic 89
Nordmende 76
Okano 60, 62, 63
Orion 70, 58*
Panasonic 16, 78, 96
Philips 83, 84, 86
Phonola 83, 84
Roadstar 47
SABA 76, 21
Samsung 93, 94, 52, 22
Sanyo 36
Schneider 84, 10
SEG 73
Seleco 47, 74
Sharp 89
Siemens 10, 36
Tandberg 26
Telefunken 91, 92
Tensai 73
Thomson 76, 100
Thorn 36, 47
Toshiba 40
Universum 92, 70, 47
W.W.House 47
Watoson 83, 58
95
97