Ethernet Connector (Rj-45 8-Pin) - Sony HDCU1000 Operation Manual

3 VBS 1 to 4 (VBS return video 1/2/3/4) connectors
(BNC-type)
Four different VBS return video input signals may be
received independently.
The selection of RET 1, 2, 3, or 4 is made by the return
switch of the video camera.
The type of input signal on RET 1, 2, 3, and 4 may be set
individually using the setup menu, or using the MSU-900
series Master Setup Unit.
An aspect ratio may also be selected for SD signals.
For details on the setup menu, contact a Sony service or
sales representative.
Refer also to the Master Setup Unit manual.
c Ethernet connector (RJ-45 8-pin)
Used to connect an Ethernet switch to construct a network
with devices, such as a Master Setup Unit of the MSU-900
series, connected to the Ethernet switch to communicate
among the devices.
As for the usable Ethernet switch, contact a Sony service
or sales representative.
Ethernet is a registered trademark of Xerox Corporation.
For details on settings for the Ethernet switch, refer to the
operation manual supplied with it.
CAUTION
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une tension
excessive à ce port.
ACHTUNG
Aus Sicherheitsgründen nicht mit einem Peripheriegerät-
Anschluss verbinden, der zu starke Spannung für diese
Buchse haben könnte.
d INPUT area
1 PROMPTER 1, 2 (tele-prompter input) connectors
(BNC-type)
Input a teleprompter signal to either of the two connectors.
The input signal is output from the other connector as is
(loop-through output). If loop-through output is not used,
terminate the unused connector at 75 ohms. If the signal
used is a 1.0 Vp-p, 75-ohm signal, it may be output from
the PROMPTER OUT connector of the video camera with
a frequency bandwidth of 5 MHz, regardless of signal
format.
2 REFERENCE connectors (BNC-type)
Input an HD tri-level reference sync signal or SD reference
sync signal (black burst signal) to either of the two
connectors.
The input signal is output from the other connector as is
(loop-through output). If loop-through output is not used,
terminate the unused connector at 75 ohms.
The type of reference signal is selected using the setup
menu, or using the MSU-900 series Master Setup Unit.
For details on the setup menu, contact a Sony service or
sales representative.
Note
To use the VBS signal of the HKCU1001 SD Encoder Unit
or the HKCU1003 Multi Interface Unit (when SC phase
lock is required), use an SD reference sync signal (black
burst signal).
e SPARE connector (BNC-type)
Reserved for future use.
f OUTPUT area
1 SYNC (sync signal output) connector (BNC-type)
Used for output of SD composite sync signal or an HD tri-
level sync signal from the internal sync signal generator.
(Factory setting: SD composite sync)
For details on the signal selection, contact a Sony service
or sales representative.
2 CHARACTER (character output) connector
(BNC-type)
Outputs the self-diagnostic results or the setup menu as an
SD monochrome analog video signal.
3 AES/EBU connector (BNC-type)
Outputs an AES/EBU format digital audio signal input to
a video camera.
g CAMERA connector (optical fiber connector)
Used to connect a video camera, using an optical fiber
cable.
All video camera signals, including power supply, control,
video, and audio, are sent and received over one optical
fiber cable.
Note
Dust on the connection surface of the optical fiber cable
may result in transmission errors.
When not connected, always cover the end of the
connector with the supplied cap.
Locations and Functions of Parts
47