Combination Mode; Combi; Combi P0: Play; 0-1: Program T01-08, 0-2: Program T09-16 - Korg M3 Owner's Manual

Combination mode

Combi Page Select
For details on how to select each page, refer to the "M3
operation guide."
Page
Select and play combinations.
Program selection for each timbre.
Pan and volume settings etc. for each timbre.
Simple KARMA editing.
P0: Play
Audio input settings and resampling
settings.
Editing from the control surface.
(☞M3 PG p.120)
Drum track settings.
X–Y control settings.
P1: DT/X–Y/Ctrls SW1, 2, and slider function settings.
Pad note and velocity settings
(☞M3 PG p.138)
EQ settings for each timbre. (☞M3 PG p.147)
P2: EQ/Option
Settings for the EXB-RADIAS option. (☞p.50)
Various parameter settings for each timbre
P3: Timbre Param (MIDI channel, OSC selection, Pitch setting,
etc.) (☞M3 PG p.149)
Key split and layer settings.
(Key zone and velocity zone)
P4: Zone/Delay
Time delay from note-on to beginning of
sound. (☞M3 PG p.153)
MIDI transmit/receive filter 1 settings. (☞M3
P5–1: MIDI Filter 1
PG p.157)
MIDI transmit/receive filter 2 settings. (☞M3
P5–2: MIDI Filter 2
PG p.160)
P7–1: KARMA1– GE Overall KARMA settings. (☞M3 PG p.161)
P7–2: KARMA2– Settings for each KARMA module. (☞M3 PG
Module p.169)
P7–3: KARMA3– KARMA GE realtime parameter settings.
GE RTP (☞M3 PG p.171)
P7–4: KARMA4– KARMA performance parameter settings.
Perf (☞M3 PG p.173)
Oscillator output bus and master effect send
P8–1: IFX Route1/ level settings.
1–5 Insert effect routing, selection, and settings.
(☞M3 PG p.177)
Bus settings for oscillator output.
P8–2: IFX Route2 Common FX LFO 1, 2 settings (☞M3 PG
p.181)
Master effect routing, selection, and settings.
P9: MFX/TFX Total effect selection and settings. (☞M3 PG
p.183)
Combi Page Select 0–1: Program T01–08, 0–2: Program T09–16
Main content

COMBI P0: Play

In this page you can select and play combinations.
In Combination mode, you can use four RADIAS programs.
0–1: Program T01–08,
0–2: Program T09–16
Here you can specify the program, Play/Mute, and Solo
On/off settings for timbres 1–8 and 9–16.
For details on selecting combinations, selecting programs,
the editable parameters, and the display, refer to the M3
operation guide and parameter guide.
R (EXB-RADIAS)
Timbres for which a RADIAS program can be used are
indicated by " ". If you select a program from bank INT-
F etc. for a timbre indicated by "
played by the EXB-RADIAS will sound.
R (EXB-RADIAS)
Use the ENABLE RADIAS setting to specify the timbres for
which a RADIAS program can be used. (☞ "Enable
RADIAS" on page 50)
Note: You can turn on Enable RADIAS for up to four
timbres. Even if you select a RADIAS program for a timbre
whose ENABLE RADIAS setting is turned off, it will not
sound.
0–3: Mixer T01–08,
0–4: Mixer T09–16
Here you can adjust the volume and pan settings for
Timbres 1–16.
For details on the available parameters and menu
commands, please see "0–3: Mixer T01–08, 0–4: Mixer T09–
16" on page 123 of the M3 parameter guide.
", a RADIAS program
47