Radias Tone Adjust Parameters - Korg M3 Owner's Manual

RADIAS Tone Adjust Parameters

OSC1 Waveform (Saw/Square/Tri/Sine/Formant/Noise/
DWGS/AudioIn, Absolute):
Selects the waveform for oscillator 1.
OSC1 Mod (Waveform/Cross/Unison/VPM, Absolute):
Selects the modulation type for oscillator 1.
OSC1 Control1 (000...127/–63...+63, Absolute):
Controls a parameter appropriate for the modulation type of
oscillator 1.
Waveform Modulation (000...127):
Controls the oscillator 1 waveform when OSC1 Mod is
Waveform.
Cross Modulation Depth (000...127):
Controls the depth of cross modulation for oscillator 1
when OSC1 Mod is Cross.
Unison Detune (000...127):
Controls the pitch difference between unison oscillators
when OSC1 Mod is Unison.
VPM Depth (000...127):
Controls the depth of the VPM effect. This can be con-
trolled if OSC1 Mod is VPM.
Formant Width (000...127):
Controls the frequency components of the formant. This
can be controlled if OSC1 Waveform is Formant.
Resonance (000...127):
Controls the amount of resonance for the noise generator.
This can be controlled if the OSC1 Waveform is Noise.
Gain (–63...+63):
Controls the volume of the audio input. This can be con-
trolled if the OSC1 Waveform is AudioIn.
OSC1 Control2 (000...127/–63...+63/01...32/
LPF63...CNT...HPF63/01...64l/L63...CNT...R63,
Absolute):
Controls a parameter appropriate for the modulation type of
oscillator 1.
LFO1 Modulation Int. (000...127):
Controls the amount of change in the oscillator 1 wave-
form. This can be controlled if the OSC1 Mod is Wave-
form or Cross.
Unison Phase (000...127):
Controls the relative phase of the oscillators at note-on.
This can be controlled if OSC1 Mod is Unison.
VPM Harmonics (01...32):
Controls the VPM modulator frequency. This can be con-
trolled if OSC1 Mod is VPM.
Formant Offset (–63...+63):
Shifts the frequency spectrum of all formants. This can be
controlled if OSC1 Waveform is Formant.
LPF/HPF Mix (LPF...CNT...HPF):
Controls the mix balance between the low pass filter and
high pass filter inside the noise generator. This can be
controlled if Waveform is Noise.
Wave Select (00...63):
Selects the DWGS waveform. This can be selected if the
OSC1 Waveform is DWGS.
Balance (L001...C064...R127):
Controls the left/right channel balance of the input sig-
nal. This can be controlled if the OSC1 Waveform is
AudioIn.
OSC2 Waveform (Saw...Sine, Absolute):
Selects the oscillator 2 waveform.
OSC2 Mod (Off/Ring...RingSync, Absolute):
Selects the modulation type for the oscillator.
OSC2 Semitone (–24...+24, Absolute):
Controls the amount of detune (semitone units) relative to
oscillator 1.
OSC2 Tune (–63...+63, Absolute):
Controls the amount of detune relative to oscillator 1.
OSC1 Level (000...127, Absolute):
Controls the output level of oscillator 1.
OSC2 Level (000...127, Absolute):
Controls the output level of oscillator 2.
Noise Level (000...127, Absolute):
Controls the output level of the noise generator.
FilterA Type/Balance
(LPF24...LPF12...HPF...BPF...THRU, Absolute):
Selects the filter type for filter A.
FilterA Cutoff (000...127, Absolute):
Controls the cutoff frequency of filter A.
FilterA Resonance (000...127, Absolute):
Controls the resonance of filter A.
FilterA EG1 Intensity (–63...+63, Absolute):
Controls the depth by which EG1 will modulate the cutoff
frequency of filter A.
FilterA Velocity Sens (–63...+63, Absolute):
Controls the depth by which velocity will modulate the
cutoff frequency of filter A.
FilterB Type (LPF...COMB, Absolute):
Selects the filter type for filter B.
FilterB Cutoff (000...127, Absolute):
Controls the cutoff frequency of filter B.
FilterB Resonance (000...127, Absolute):
Controls the resonance of filter B.
FilterB EG1 Intensity (–63...+63, Absolute):
Controls the depth by which EG1 will modulate the cutoff
frequency of filter B.
FilterB Velocity Sens (–63...+63, Absolute):
Controls the depth by which velocity will modulate the
cutoff frequency of filter B.
Drive/Wave Shape SW (Off/Drive/Wave Shape, Absolute):
Selects drive or wave shape.
Drive/WS Position (Pre Filter1/Pre Amp, Absolute):
Selects the position at which drive or wave shaping will be
applied.
Drive/WS Depth (000...127, Absolute):
Controls the depth of drive or wave shaping.
Wave Shape Type (Decimator...Level Boost, Absolute):
Controls the wave shape type.
Punch Level (000...127, Absolute):
Controls the mix amount of pulse wave added to the
oscillator output.
LFO1 Waveform (Saw/Square/Triangle/S&H, Absolute):
Selects the LFO1 waveform.
LFO1 Shape (–63...+00...+63, Absolute):
Controls the LFO1 waveform.
LFO2 Waveform (Saw/Square+/Sine/S&H, Absolute):
Selects the LFO2 waveform.
LFO2 Shape (–63...+00...+63, Absolute):
Controls the LFO2 waveform.
Mod SEQ SW (Off/On, Absolute):
Controls the on/off status of the modulation sequence.
MSEQ Seq Type (Forward/Reverse/Alt1/Alt2, Absolute):
Selects the sequence type for the modulation sequence.
MSEQ Last Step (01...16, Absolute):
Controls the number of steps in the modulation sequence.
PROG P0: Play Tone Adjust
23