Infra-Red Remote Control & Codes - Bryston SP3 Manual

IR REMOTE CONTROL
The SP3 Remote Control can operate all front panel operations in addition
to having a MUTE button to for quickly silencing the output of the SP3.
Several other functions are accessible by sending 3 digit numeric codes to
the SP3. To send codes to the SP3:
1: Press and hold the CODE button until the status LED on the remote
(located between the CODE and POWER buttons) flashes a couple
of times & then stays lit steadily red; then release
2: Within a few seconds, while the status LED remains steadily lit, enter
the desired 3 digit numeric code (see the table below for valid codes).
Refer to the BR3 illustration below for the location of the number keys
on the remote.
3: When a valid code has been entered the LED will flash twice to con-
SP3 IR-CODES
Function Code
Reserved (was PwrOff) 000 Mode None
Source TV/SAT 001 Dolby Pro Logic
Source DVD 002 PLII Music
Source CD 003 PLII Movie
Source TUNER 004 Neo-6 Music
Source DVR 005 Neo-6 Movie
Source TAPE 006 Stereo 7
Volume Up 007 Party
Volume Down 008 Hall
Mute Toggle 009 Church
Pink Noise Test 010 Stadium
Digital Toggle 011 Club
Dolby EX Force/Auto 012 Theatre
Stereo Toggle 013 Natural
Zone / Mute Toggle 014 Dolby Digital 5.1
Power On/Off 015 Dolby Digital EX Movie
DTS ES Force/Auto 016 PLIIx Music 6
017 PLIIx Movie 7
018 PLIIx Music7
Menu Up 019 PLIIx Auto
Menu Down 020 Stereo7
021 HDMI Toggle
Centre 022 Source BAL-1
Side Surround 023 Source BAL-2
Back 024 Source USB
Subwoofer 025 Main / Mute Toggle
Save, Exit Menu 026
2-Ch Bypass Toggle 027
Source 7.1 Bypass 028
Power On 029
030 Surround Left
031 Surround Right
032 Menu Left
033 Menu Right
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
Mono 052
2-Ch Bypass On 053
054
2-Ch Bypass Off 055
Digital On 056
Digital Off 057
Mute On 058
Mute Off 059
Bypass Subw On/Off 060
061
062
063
Rev. 703-02
(updated 7-Aug-2013)
Function Code Function Code
064 128
065 129
066 130
067 131
068 132
069 133
070 134
071 135
072 136
073 137
074 138
075 139
076 140
077 141
078 142
079 143
080 144
081 145
082 146
083 147
084 148
085 149
086 150
087 151
088 152
089 153
090 154
091 155
092 156
093 157
094 158
095 159
096 160
097 161
098 162
099 163
100 164
101 165
102 166
103 167
104 168
105 169
106 170
107 171
108 172
109 173
110 174 Power OFF
111 175 Power ON (reserved)
112 176 DISPLAY Toggle
113 177 Default EEPROM
114 178
115 179
116 180
117 181
118 182
119 183
120 184
121 185
122 186
123 187
124 188 Default TCP/IP
125 189
126 190
127 191 Reserved (was REBOOT)
Certain features in the remote control itself
can also be programmed by entering codes as
described above. The only differece is that these
codes affect only the BR3 remote control itself
and are not sent to the SP3. These codes are
as follows:
792: Toggle motion sensor on/off (backlight
control)
797: Toggle backlight on/off
Function Code
192
193
194
195
When enabled, the backlight will only come on when the
196
197
ambient light falls below a predetermined level . If the
198
motion detector (code 792) is disabled then the backlight
199
will come on only when a button is pressed AND the ambi-
200
201
ent light level is low enough . If both the backlight and the
202
motion detector are both enabled the backlight will come
203
204
on when the unit experiences movement and/or when any
205
of the buttons are pressed AND the ambient light is low
206
enough .
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
Test LEDs 245
246
247
248
249
250
251
252
253
254
255
Dec 6, 2012
firm that the code has been accepted.
BACKLIGHT OPERATION