Infra-Red Remote Control & Codes - Bryston SP3 Owner's Manual

IR REMOTE CONTROL
The SP3 Remote Control can operate all front panel
operations in addition to having a MUTE button to for
quickly silencing the output of the SP3.
Several other functions are accessible by sending 3 digit
numeric codes to the SP3. To send codes to the SP3:
1: Press and hold the CODE button until the status
LED on the remote (located between the CODE
and POWER buttons) flashes a couple of times &
then stays lit steadily red; then release
2: W ithin a few seconds, while the status LED remains
steadily lit, enter the desired 3 digit numeric code
(see the table below for valid codes). Refer to the
Function
Power Off (Standby)
Source TV/SAT
Source DVD
Source CD
Source TUNER
Source DVR
Source TAPE
Volume Up
Volume Down
Mute Main or Zone tog
Pink Noise Test
Digital toggle
Dolby EX Force/Auto
Stereo toggle
Zone/Zmute toggle
Power/Standby toggle
DTS ES Force/Auto
Surround On
Surr Right arrow/Mode
Menu Up arrow
Menu Down arrow
Select button
Centre Speaker
Rear Speaker
Back Speaker
Subwoofer Speaker
Save Config
2-Ch Bypass toggle
Source 7 .1 Bypass
Power On
n/a
OSD On/Off
OSD Off
OSD On
MONO On
2-Ch Bypass On
Source 7 .1 Bypass
2-Ch Bypass Off
Digital On
Digital Off
Mute Main or Zone On
Mute Main or Zone Off
Rev . 701-01
Code Function
0 Sub in Bypass toggle
1 SurrEff2 None
2 SurrEff2 Pro-Logic
3 SurrEff2 NonePLII Music
4 SurrEff2 PLII Movie
5 SurrEff2 Neo-6 Music
6 SurrEff2 Neo-6 Movie
7 SurrEff2 Stereo 7
8 SurrEff Party
9 SurrEff2 Hall
10 SurrEff2 Church
11 SurrEff2 Stadium
12 SurrEff Club
13 SurrEff2 Theatre
14 SurrEff2 Natural
15 SurrEff7 DD 5 .1
16 SurrEff7 DD EX Movie6
17 SurrEff7 PLIIx Music6
18 SurrEff7 PLIIx Movie7
19 SurrEff7 PLIIx Music7
20 SurrEff7 PLIIx AUTO
21 SurrEff2 Stereo7x
22 HDMI toggle
23 Source BAL1
24 Source BAL2
25 Source USB
Main/Mmute toggle
26
27 n/a
28 Surr Left arrow
29 Surr Right arrow
Menu Left arrow
30-48
49 Menu Right arrow
50 n/a
51 HiddenMenuUnlock
n/a
52
53 Reserved
54 Reserved
55 DISPLAY toggle
56 n/a
57 TEST LEDs & DISP
58 n/a
59 System RST&REBOOT
Stan B. 15-Feb-2012
BR3 illustration below for the location of the num-
ber keys on the remote.
3: W hen a valid code has been entered the LED
will flash twice to confirm that the code has been
accepted.
Certain features in the remote control itself can also be
programmed by entering codes as described above.
The only differece is that these codes affect only the
BR3 remote control itself and are not sent to the SP3.
These codes are as follows:
792: Toggle motion sensor on/off (backlight control)
797: Toggle backlight on/off
Code
60
When enabled, the backlight will only come on when the ambi-
64
ent light falls below a predetermined level . If the motion detec-
65
tor (code 792) is disabled then the backlight will come on only
66
when a button is pressed AND the ambient light level is low
67
enough . If both the backlight and the motion detector are both
68 enabled the backlight will come on when the unit experiences
movement and/or when any of the buttons are pressed AND
69
the ambient light is low enough .
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90-93
94
95
96
97
98-221
222
223-237
238
239
240
241-244
245
246-254
255
BACKLIGHT OPERATION