Ir Remote Control - Bryston SP3 Owner's Manual

IR REMOTE CONTROL

The SP3 Remote Control can operate all front panel
operations in addition to having a MUTE button to for
quickly silencing the output of the SP3.
Several other functions are accessible by sending 3 digit
numeric codes to the SP3. To send codes to the SP3:
1: Press and hold the CODE button until the status
LED on the remote (located between the CODE
and POWER buttons) flashes a couple of times &
then stays lit steadily red; then release
2: W ithin a few seconds, while the status LED remains
steadily lit, enter the desired 3 digit numeric code
(see the table below for valid codes). Refer to the
Function
Power Off
TV/SAT
DVD
CD
TUNER
DVR
TAPE
Volume Up
Volume Down
Mute
Test
DIG,HDMI,ANA
Dolby
Stereo
ZONE2, MAIN
STANDBY
DTS
Surround
SURR 
Menu Up
Menu Down
SEL
Centre
Rear
Back
Subwoofer
EXIT 
BP2
7.1BP
Power On
OSD On/Off
OSD Off
OSD On
Mono
2-Ch Bypass On
7.1BP
BP2OFF
Digital On
Digital Off
Mute On
Mute Off
Bypass Sub On/Off
DIGI FORCE ON
DIGI FORCE OFF
Items in italics may not yet be implemented
Code Function
000 EF00 (no effect)
001 EF01 (ProLogic)
002 EF02 (PLIIx Music)
003 EF03 (PLIIx Movie)
004 EF04 (Neo:6 Music)
005 EF05 (Neo:6 Movie)
006 EF06 (Stereo5)
007 EF07 (Party)
008 EF08 (Hall)
009 EF09 (Church)
010 EF10 (Stadium)
011 EF11 (Club)
012 EF12 (Theater)
013 EF13 (natural)
014 DD/DTS 5.1 SM01
015 DD ex MOVIE 6.1 SM02
016 PLIIx MUSIC 6.1 SM03
017 PLIIx MOVIE 7.1SM04
018 PLIIx MUSIC 7.1 SM05
019 PLIIx AUTO SM06
020
021 HDMI
022 BAL1
023 BAL2
024 USB
MAIN
025
026
027 Trigger OFF
028 Trigger ON
029 VFD DISPL
Init EEPROM Params
049 Restore Pic32 factory
050 Update Pic32 user
051 Trigger Delay
052 TEST LED
053
054 Update DAE
055 Volume Calib
056 Turning Point
057 Auto Save On/Off
058 X-Over On/Off
059 Init TCP/IP
060 Power-up option
061
062
REBOOT
BR3 illustration below for the location of the num-
ber keys on the remote.
3: W hen a valid code has been entered the LED
will flash twice to confirm that the code has been
accepted.
Certain features in the remote control itself can also be
programmed by entering codes as described above.
The only differece is that these codes affect only the
BR3 remote control itself and are not sent to the SP3.
These codes are as follows:
792: Toggle motion sensor on/off (backlight control)
797: Toggle backlight on/off
Code
064
BACKLIGHT OPERATION
065
When enabled, the backlight will only come on when the ambi-
066
ent light falls below a predetermined level . If the motion detec-
067
tor (code 792) is disabled then the backlight will come on only
068
when a button is pressed AND the ambient light level is low
069
enough . If both the backlight and the motion detector are both
070
enabled the backlight will come on when the unit experiences
071
movement and/or when any of the buttons are pressed AND
072
the ambient light is low enough .
073
074
075
076
077
078
079
080
081
082
083
085
086
087
088
089
238
239
240
241
242
243
244
245
247
248
249
250
251
252
253
254
255
SP3 PREAMP / PROCESSOR
1 2 3
4 5 6
7 8 9 0