Important safety instructions Device summary Initial use Unpacking the device / checking the package contents Inserting the batteries Operating components LCD display Buttons SETUP - System settings Code Setup (Programming the remote control) Programming by brand code search Programming by manual code input Programming by automatic code search System-Setup Setting the time...
Proper use Children may only operate the remote control under adult supervision. The universal remote control can replace a maximum of ten remote controls. It can only be used for entertainment elec- tronics with infrared receivers. The functions of the Universal remote control essentially correspond to those of the original remote control.
Damage to the device • If the device is defective, do not attempt to repair it your- self. In case of damage, contact the manufacturer or the manufacturer's service hotline (see Warranty information). • If liquid escapes from the device or if the device has been otherwise damaged, it must be inspected by the manufac- turer or the manufacturer's service hotline.
Service-Hotline (see warranty information). Inserting the batteries Attention! The Universal remote control must only be operated with 1.5 Volt batteries (Type AAA, LR03). Carry out the battery change as quickly as possible. Preset settings will remain saved for approx. 1 minute. If new batter- ies have not been installed within this time all of the settings will have to be carried out again.
Note: If no LCD display q is visible check the polarity of the batteries or install new ones. Operating components LCD display The LCD display q is divided into fields. Text field 2! Here is shown the currently selected device, for example DVD, TV VCR etc.
The standard readout of the LCD display q consists of the details for the relevent device, for example, "TV", the initial for the day of the week and the time of day indicator. Buttons Note: All the functions described here can, of course, only be used if they are supported by the device being controlled.
Page 9
CH +/— buttons u MACRO button i Number buttons o Button for one/two digit programme numbers a Teletext function buttons s In teletext operation the buttons have the following functions: Note: The function is only available in the European TV mode and your TV device must have a teletext module.
Record/playback buttons f The playback buttons f control devices such as DVD/CD players and video recorders: Mute switching g Switch sound on/off. VOL+/— buttons h Set volume (Volume). MENU button j Access the menu of the controlled device. OK button k You can confirm a menu selection with the OK button.
3 Programming methods are available for the remote control: Programming by brand code search, by automatic code search and by direct code input (manual). First you should use the brand code search since this method is the fastest way of programming if the manufacturer of your de- vice is itemized in the code list.
9. If most of the buttons function press the OK button k to save the setting. In the LCD display q "OK" appears. Now the mode "BRAND CODE" appears again. 10. If, however, none or only a few of the buttons function select with the ...
Page 14
1. Press the device button e for the device that is to be con- trolled (i.e. VCR). 2. Switch the device that is to be controlled with the remote control on. With VCR/DVD/CD devices please insert a tape and/or disc. 3. Hold down the S button r for a little longer than 3 sec- onds.
Setting the time The LCD display q shows you the time of day. You set this as follows: 1. Hold down the S button r for a little longer than 3 seconds. The notice "CODE SETUP" appears. If appox. 15 seconds passes without an entry the device exits the menu and returns to the standard display.
Adjust contrast You can set the display's contrast as follows: 1. Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears. 2. With the or button t select "SYSTEM SETUP" and confirm with the OK button k.
The URC offers 2 timer modes, sleep timer and event timer. Sleep timer 1. Press the device button e for the device that is to be con- trolled (i.e. VCR). 2. Hold down the S button r for a little longer than 3 sec- onds.
15 seconds without an entry. Learn Setup The Universal remote control (URC) can learn and save but- ton signals of an original remote control. If the URC does not work after applying the programming methods already de- scribed or cannot carry out all commands please attempt to teach the URC with the help of the original remote control.
5. First press the button on the URC that is to be taught. In the LCD display q "LEARNING" appears. The URC now waits for the infrared signal from the original remote control. Note: Should the notice not change to "LEARNING" you have selected a button for which no button code can be taught.
Page 20
To programme a Macro For Macro programming proceed as follows: 1. Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears. 2. With the or button t select "MACRO SETUP" and confirm with the OK button k.
To delete all Macros To delete all pre-programmed Macros proceed as follows: 1. Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears. 2. With the or button t select "MACRO SETUP" and confirm with the OK button k.
Note: The input of the channel numbers can vary according to the model and brand of the selected devices. If necessary, with multi-digit channel numbers you must first press the button a. To access favourites To access a pre-programmed favourite press the FAV/EPG button l followed by the corresponding number button for the desired memory slot (1 - 4).
> To operate one of the programmed devices with the URC first press the corresponding device button e. Then point the URC to this device and press the desired button. > Put the number buttons original remote control. Before you make a two digit entry press, if necessary, the >...
This product is subject to the European directive 2002/96/EC. Universal remote control • Have the universal remote control or parts of it disposed of by a professional disposal company or by your commu- nal disposal facility. • Observe the currently applicable regulations. In case of doubt contact your disposal facility.
Dispose of packaging materials in an environmentally responsible manner. CE- Conformity This device satisfies the fundamental requirements and other relevant regulations of the EMC Directive 2004/108/EC. Importer KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM, GERMANY www.kompernass.com Technical data Controllable devices: Dimensions...
Page 26
Your statu- tory warranty claims are not restricted by this warranty. DES Ltd Tel.: 0870/787-6177 Fax: 0870/787-6168 e-mail: support.uk@kompernass.com Kompernass Service Ireland Tel: 1850 930 412 Standard call rates apply. Mobile operators may vary. e-mail: support.ie@kompernass.com (0,082 EUR/Min.) - 24 -...