Universal Electronics Contour User Manual

Nebula Contour.fm Page 1 Wednesday, June 24, 2009 1:46 PM
Contour NOTE: When the battery voltage is low, the TV or
STB key blinks 5 times after a keypress.
STEP 2: PROGRAM FOR TV
CONTROL
The Contour remote control is preprogrammed to
control your set-top box
but it must be manually programmed in order to
control the TV power and volume.
Follow the instructions below to program your
remote for your TV.
1. Turn on the TV.
2. Press the TV key on the remote.
3. Press and hold SETUP until the TV key
blinks twice, then release.
4. Enter the first five-digit code for the TV
brand that you wish to program.
5. The LED blinks once as each digit is
entered. If the code is valid, the LED blinks
twice.
NOTE: If the LED does not blink twice, repeat
steps 2 to 4 and try entering the code again.
6. Aim the remote at the TV and press MUTE.
The TV volume should mute. If it does not,
repeat steps 3–5, trying each code for your
brand until you find one that works. If you
cannot find a code that works, see
"Searching for Your Code".
SEARCHING FOR YOUR CODE
If your TV does not respond to the remote after
trying all codes listed for your brand, or if your
brand is not listed, try searching for your code:
1. Turn the TV on.
2. Press the TV key once.
3. Press and hold SETUP until the TV key
blinks twice, then release.
4. Enter 9 9 1. The TV key blinks twice.
5. Press and Release Digit 1 (The TV key blinks
twice).
6. Aim the remote at the TV. Press and release
User's Guide
POWER.
7. While aiming the remote at the TV, press
By UNIVERSAL ELECTRONICS
CH+ and the remote will test the next TV
code. Press CH+ repeatedly until the TV
turns off.
GETTING STARTED
Note: Press CH- to try the previous code.
The Contour remote control is intended to be 8. Now that you have found the correct code,
simple to set-up and to use. Just follow the two press SETUP to save the code for your TV.
steps below and the remote will be ready for use
in just a few short minutes.
CHANGING VOLUME LOCK
STEP 1: INSTALL BATTERIES
The Contour remote control comes preset with
volume controls (Volume Up, Volume Down, and
Your Contour remote control requires 2 AA MUTE) all l cked to your TV. This section describes
batteries (included).
how to disable and enable volume lock.
Battery Use And Safety Locking Volume Control
• Use only fresh batteries of the required size
1. Press and hold SETUP until either the TV or
and recommended type.
STB key blinks
• Do not mix old and new batteries, different
twice.
types of batteries (standard,alkaline, or
2. Enter 9 9 3, the LED blinks twice.
rechargeable), or rechargeable batteries of
3. Press the mode key for the device you want
differentcapacities.
to control (for example, TV).
• If you do not plan to use the remote for an
4. The LED blinks twice. Now when you press
extended period, remove the battery. It can
VOL+, VOL-, or MUTE, the selected device
leak chemicals that can destroy electronic
(for example, TV) controls the volume
parts.
regardless of the current mode.
WARNING: Dispose of old batteries promptly and
Unlocking All Volume Control
properly. Do not burn or
1. Press and hold SETUP until either the TV or
bury them.
STB key blinks
To Install Batteries: twice, then release.
2. Enter 9 9 3, the LED blinks twice.
1. Open the battery compartment cover
3. Press VOL+. The LED blinks four times.
(located on the back of the remote).
Volume is independently controlled for all
2. Place the AA batteries in the compartment
programmed devices.
and match the + and -polarity symbols
inside.
3. Replace the cover.
PROGRAMMING MACROS
Press this key...
Raise or lower the sound level.
Your Contour remote control includes the ability
Press MUTE to turn the sound off
to program the A, B, C, and D keys with a Macro
function. Each one can be set up to perform a pre-
or on.
programmed set of sequential key presses with
the press of
Move the cursor in the menu
one key. A macro can be used to control a home
theater operation, to set a favorite channel, or for
screens.
other multiple functions you would like to control
Press OK to choose the
with one key press. Moreover, each Macro Key can
highlighted menu option.
hold up to 15 key presses total.
You can program a macro that operates regardless
Rewind, fast forward, pause, or
of what mode you are in, or one that only operates
play to control an ON DEMAND
when you are in a specific mode.
movie or recorded show.
NOTE: Programming a new macro over an
existing one erases the original macro.
View the current channel and
program information.
Programming a Macro
1. Press and hold SETUP until either the TV or
Display the menu for the
STB key blinks
selected device.
twice, then release.
2. Press 9 9 5. The TV or STB key blinks twice.
3. Press the key you wish to assign a macro on. Exit the selected device's menu,
4. Enter the series of commands you want the
guide, or program without
macro to execute (up to 15 commands).
making a menu selection.
5. Press and hold SETUP until either the TV or
STB key blinks twice, then release.
Display the program guide for
Now, when you press the preset macro key, the
the selected device.
remote sends the series of commands you have
entered, regardless of what mode you are in. For
Switch the TV's input to view
example, you could program a macro key to turn
on both your TV and cable box and select a TV or video programs.
particular channel.
Directly enter channels (for
To clear the macro, repeat steps 1-5 above, but do
example, 09 or 31).
not enter a series of commands at step 4.
Press Enter to send channel
TROUBLESHOOTING
number entries on some TV
models.
PROBLEM: TV or STB key does not blink when
Use the A, B, C, and D keys for
you press a key.
programming macros. (See
SOLUTION: Try pressing different keys. Replace
"Programming
the batteries with 2 new AA batteries.
Macros".)
PROBLEM: LED blinks when you press a key, but
device does not respond.
MANUFACTURER'S CODES
SOLUTION: Make sure the remote is aimed at your
device and is not more than 40 feet away.
PROBLEM: LED blinks one long blink while in
Setup Codes for TVs
SETUP mode.
A-Mark 10047, 10054, 10165
SOLUTION: An entry error has occurred (for
Accuscan 10047, 10018, 10135
example, wrong key). Try entry sequence again.
Action 10030, 10185
PROBLEM: Remote does not control devices or
Admiral 10047, 10054, 10017, 10051,
commands are not working properly.
10093, 10463, 10180, 10018,
SOLUTION: Try all listed codes for the device.
10165
Make sure the device operates with an infrared
remote control.
Advantz 10282
PROBLEM: No volume on a device. Advent 10761, 10783, 10815, 10817,
10842, 11933
SOLUTION: See "Changing Volume Lock".
Adventuri 10000
A QUICK LOOK AT THE CONTROLS
Agna 10150
Aiko 10092
Press this key... To...
Akai 10060, 10812, 10702, 10030,
10145, 10151, 10672, 11903,
Select a device (either TV or
11935
STB).
Albatron 10700, 10843
Turn the selected device on or
Alfide 10672
off.
Alleron 10030
Program sequences.
Ambassador 10150, 10177
America Action 10180
American High 10000, 10060
Select the next or previous
Ampro 10751
channel.
Amstrad 10171, 10177
Amtron 10000, 10180
Anam 10180
Anam National 10055
AOC 10180, 10030, 10185 Electrograph
To...
Apex Digital 10156, 10748, 10879, 10765, Electrohome
10185, 10767, 11943
Audinac 10180 Emerald
Audiovox 10451, 10180, 10092, 10623, Emerson
10802, 10875, 11937, 11951,
11952
Aventura 10171
Axion 11937
Envision
Baysonic 10180
Epson
Beaumark 10017, 10178, 10030
ESA
Belcor 10030
Fisher
Bell & Howell 10054, 10154, 10093
Fortress
BenQ 11032
Fujitsu
Boxlight 10893
Funai
Bradford 10180
Futuretech
Brockwood 10178, 10030
Gateway
Broksonic 10236, 10463, 10180, 10177,
GE
11929, 11935, 11938
Candle 10030
Capehart 10017, 10178, 10030, 10092
Carnivale 10030
Carver 10054
Gemini
Celebrity 10000
Gibralter
Celera 10765
Go Video
Changhong 10156, 10765, 10767, 10783
Go Vision
Cineral 10451, 10092
GoldStar
Citek 10047
Citizen 10054, 10000, 10451, 10463,
Gradiente
10180, 10060, 10030, 10171,
Grundig
10092, 10282, 11928
Grundy
Civet 10185
Grunpy
Clairtone 10185
Haier
Clarion 10180
Hallmark
Classic 10030, 10092
Colortyme 10047, 10054, 10017, 10060,
Harley Davidson
10178, 10030, 10018
Commercial Solutions 11447, 10047
Harman/Kardon
Conic 10178
Harvard
Contec 10180, 10185
Havermy
Craig 10180, 10171, 10282
Heathkit
Crosley 10054, 10000, 10180, 10030,
Helios
10171, 10187
Hello Kitty
Crown 10093, 10180, 10672
Hewlett Packard
Crown Mustang 10672
Hisense
Curtis Mathes 10047, 10054, 10154, 10000,
Hitachi
10051, 10451, 10093, 10180,
10060, 10702, 10178, 10030,
10145, 10166, 10018, 10466,
11147, 11347, 11919
HP
CXC 10180
Hyundai
Cytron 11326
Ima
Daewoo 10451, 10178, 10092, 11661,
Infinity
10623, 10661, 10672, 11755,
Insignia
11756, 11928
Inteq
Dayton 10092
JBL
Daytron 10178, 10030, 10092
JCB
Dell 11080, 11178
Jensen
Denon 10145, 10055, 10511
JIL
Denstar 10628
Jutan
Digital Life 10872
JVC
Dumont 10017, 10180, 10178
Durabrand 10463, 10180, 10178, 10171,
Kamp
11034
Kawasho
Dwin 10093, 10720, 10774
KEC
Eaton 10060
Kenwood
Electroband 10000, 10185
11755 KLH 10156, 10180, 10765, 10767
10154, 10000, 10150, 10178, Kloss 10030
10030, 10151, 10185
Konka 10180, 10080, 10628, 10632,
10178, 10177 10638, 10703, 10707, 10720
10047, 10154, 10451, 10236, Kost 11262
10463, 10180, 10150, 10178,
KTV 10463, 10180, 10030, 10185
10171, 11944, 11929, 11928,
Lark 10154
10623, 10282, 10185, 10177,
LG 10054, 11265, 10060, 10178,
10135
10030, 10700, 10856, 11154,
10030, 10813
11178, 11758
10833, 10840
Lloyd's 10236, 10180, 10030, 11904
10812, 10171, 11944
Logik 10236, 10180
10054, 10154, 10000, 10159
LXI 10047, 10054, 10017, 10154,
10093
10000, 10156, 10051, 10093,
10683, 10809, 10853 10060, 10053, 10178, 10030,
10171, 10166, 10055, 10135,
10000, 10180, 10171, 11904
10018, 10159, 10165
10180
Magnasonic 10054, 10000, 10156, 10093,
11755, 11756
10030, 10092, 11928
11447, 10047, 10000, 10051,
Magnavox 10047, 11454, 10054, 10154,
10451, 10060, 10178, 10030,
10000, 10250, 10051, 10180,
10135, 10055, 10282, 11147,
10060, 10030, 10171, 10092,
11347, 10018, 11917, 11919,
10706, 10187, 10282, 10386,
11922
10802, 11254, 11755, 11904,
10047
11931, 11944
10017, 10000, 10030
Majestic 10017
10886
Marantz 11454, 10054, 10030, 10704,
11937
10854, 10855, 11154
10047, 10054, 10178, 10030,
Matsui 10177
10018, 11154, 11926
Matsushita 10250, 10051, 10650
10053
Maxent 11755, 11756
10706, 10672, 10683
Megapower 10700
10180
Megatron 10047, 10178, 10145, 10151
10180
MEI 10185
11034, 10768
Memorex 10154, 10463, 10180, 10150,
10236, 10180, 10178, 10135,
10178, 10030, 10165, 11926
10187
MGA 10150, 10178, 10030
10000, 10180, 10060, 10178,
MGN Technology 10178
10030, 11904
Micro Genius 10150
10054
Midland 10047, 10017, 10051, 10018,
10180
10135
10093
Mitsubishi 10154, 10250, 10093, 11250,
10017
10150, 10178, 10030, 10836,
10865
10868, 11917
10451
Monovision 10700, 10843
11089, 11494, 11502
Motorola 10054, 10051, 10093, 10150,
10748 10055
10047, 10054, 10017, 10000, MTC 10180, 10060, 10030, 10092,
10051, 10178, 11145, 10145, 10185, 10282
10018, 10055, 10151, 10185,
Multitech 10180
11904, 11960
NAD 10156, 10178, 10166, 10866
11089, 11494, 11502
NEC 10047, 10156, 10178, 10030,
10849, 10865
10497, 10704, 10882, 11704
10236, 10180, 10178
NetTV 11755
10054
Nikko 10178, 10030, 10092
10171, 11326, 11517
Nikkodo 10178, 10030, 10092
10017, 10145
Nishi 10030, 10018
10054
Norcent 10748, 10824, 11089
10000
Noshi 10018
10761, 10815, 10817, 11933
NTC 10092
10030
Nyon 10000
10030
Olevia 11144, 11240, 11331
10054, 10053, 10030, 10055,
Onwa 10180
10731, 11253
10154, 10250, 10093,
10017, 10180, 10185 Optimus
10180,
10030, 10185
10150, 10178, 10030,
10180, 10060
10166, 10165, 10650
10180, 10030
Optoma 10887