Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Operator's Manual
Manual del operador
Manuel de l'utilisateur
EN
English (2 - 23)
ES
Español (24 - 45)
FR
Français (46 - 67)
U.S. Patent No. 6,760,947; No. 6,105,192; No. 6,493,896 (Deluxe Machines); & Patent Pending
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your Clarke machine could
result in injury to you or to other personnel; damage to the machine or to other property could occur as
well. You must have training in the operation of this machine before using it. If your operator(s) cannot
read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: Clarke
Form No. 70951A 1/09
®
, 2100 Highway 265, Springdale, Arkansas 72764.
Clarke
®
24V Model
C28, C33
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
Printed in the U.S.A.
Advertisement
Chapters
Table of Contents
Related Manuals for Clarke Focus C28
Summary of Contents for Clarke Focus C28
- Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
-
Page 2: Table Of Contents
Control Panel Connection Diagram ........................ 88 Front of Machine Connection Diagram ......................88 Electrical Plate Connection Diagram ....................... 89 Control Housing Connection Diagram ......................90 Electrical Schematic ............................91 ® Clarke Page Operator's Manual (EN) - FOCUS C28 and C33... -
Page 3: Operator Safety Instructions
Failure to read the Owner's Manual prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. -
Page 4: Introduction
Clarke's newly designed C28 and C33 automatic scrubbers are efficient and superior floor cleaning machines. The Focus C33 uses two brushes or pads to scrub a path 33 inches wide. The Focus C28 uses two brushes or pads to scrub a path 28 inches wide. A squeegee wipes the floor while the vacuum motor removes the dirty solution from the floor - all in one pass. -
Page 5: Machine Specifications
28 inch (71 cm) Grade Cleaning 6° Incline 6° Incline Weight w/Batteries (310AH) 1015 lbs. 460kg 1005 lbs. 456kg Shipping Weight 1318 lbs. 598kg 1308 lbs. 593kg w/batteries (310AH) ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 5 -... -
Page 6: Procedures For Transporting
9. Replace squeegee assembly, brush housings, & brushes or pad drivers after the machine is unloaded and ready to use. ® Clarke Page Operator's Manual (EN) - FOCUS C28 and C33... -
Page 7: Symbols Used On C28, C33
SYMBOLS USED ON FOCUS C28, C33 Hazard Alert Symbol Charge/Battery Meter On/Off Key Switch Warning Label (with parking brake) Brush Up/Down Solution Control Warning Label (without parking brake) Power Traverse Speed Control ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 7 -... -
Page 8: Machine Control Panel C28, C33
Hour Meter (See Figure #1, Item "M") The hour meter indicates the number of hours the machine has operated. It runs only when the machine is moving forward or reverse. ® Clarke Page Operator's Manual (EN) - FOCUS C28 and C33... - Page 9 ENGLISH MACHINE CONTROL PANEL C28, C33 Figure #1 ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 9 -...
-
Page 10: Machine Controls And Features
The shut-off switch for the vac motor is located in the recovery tank. It automatically turns off the vac motor when the recovery tank is full. Figure #3b Figure #4 Figure #3c Figure #5 ® Clarke Page -10- Operator's Manual (EN) - FOCUS C28 and C33... -
Page 11: How To Prepare The Machine For Operation
8. Install the tank, reconnecting hoses and plugging in vac motor and float switch connectors. Install tank support bracket. NOTE: Charge the batteries before using the machine. Figure #6b ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 11 -... -
Page 12: Battery Maintenance
To clean the terminals and connectors, use a terminal and connector cleaning tool. Do not allow ammonia or bicarbonate of soda to get into batteries. 3. Keep the batteries charged. ® Clarke Page -12- Operator's Manual (EN) - FOCUS C28 and C33... -
Page 13: How To Charge The Batteries
When recharging the batteries, keep the recovery tank open. After every 20 recharging cycles, check the level of the electrolyte and if necessary top off with distilled water. ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 13 -... -
Page 14: How To Install The Brushes Or Pad Drivers
3. Turn the key switch "OFF". 4. Go to the front of the machine. 5. Push down on two sides of the brush or pad driver until the gimbals release. ® Clarke Page -14- Operator's Manual (EN) - FOCUS C28 and C33... -
Page 15: How To Operate The Machine
5. When filling the machine from the rear, position the clear drain hose against bracket and insert hose as shown in figure 16. Solution level can be viewed from the back of the machine. Figure #16 ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 15 -... -
Page 16: How To Traverse Machine
NOTE: When you make more passes across the floor, let the brushes clean approximately 2 inches of the area already cleaned by the brushes. NOTE: During most cleaning procedures, apply and remove the solution in one operation. ® Clarke Page -16- Operator's Manual (EN) - FOCUS C28 and C33... -
Page 17: Maintenance
6. Make sure brush housings and skirts are in position on the brush head. 7. Make sure the brushes are in position and installed correctly 8. Check the installation of the squeegee and squeegee hose. ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 17 -... - Page 18 Use a clean cloth and wipe the surface of the machine. Charge the batteries. See the instruction in the section of this book called “How To Charge The Batteries”. ® Clarke Page -18- Operator's Manual (EN) - FOCUS C28 and C33...
- Page 19 5. Use a grease gun to lubricate the drive wheel and the casters. See figure #25. 6. Check tire pressure. Tire pressure should be about 50 psi. ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 19 -...
- Page 20 "Y" up. Make very small adjustments and try it until a uniform flare is achieved. Changing the tilt may also require readjusting the squee- gee pressure. ® Clarke Page -20- Operator's Manual (EN) - FOCUS C28 and C33...
- Page 21 (figure 31, B) and clean or replace it. Turn solution valve back on (figure 31, A) and push filter assembly back inside frame. Figure #30 Figure #31 ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 21 -...
-
Page 22: How To Correct A Problem
Check wire connection to traverse motor. Replace the fuses. Check the batteries connections. Check parking brake overide lever position (if installed) NOTE: If the motors continue to stop, consult an authorized service person. ® Clarke Page -22- Operator's Manual (EN) - FOCUS C28 and C33... -
Page 23: Accessories
Soft Nylon 11428B 14" Poly 11427B 14" Grit-Heavy 11426B 14" Grit-Medium 11431B 14" Grit-Lite 10383A 14" Soft Nylon 11429B Pad Drivers: Size Part No. 17" 17520C 14" 17521C ® Clarke Operator's Manual (EN) - FOCUS C28 and C33 - 23 -... - Page 24 Este manual contiene información importante acerca del uso y la seguridad de la máquina. Si no lee el manual antes de utilizar su máquina Clarke o de intentar realizar los procedimientos de reparación o mantenimiento de la misma, usted o el resto del personal podrían sufrir lesiones; asimismo, podrían producirse daños a la máquina o a otras propiedades.
-
Page 25: Instrucciones De Seguridad Para El Operador
Usted o el resto del personal pueden sufrir lesiones si no leen el manual de instrucciones antes de operar, intentar reparar o realizar mantenimiento a su máquina Clarke. Asimismo, pueden producirse daños a la máquina o a otras propiedades. Antes de utilizar la máquina, es necesario recibir la capacitación adecuada en la operación de la misma. -
Page 26: Introducción
Introducción Introducción: Los nuevos modelos de fregadora automática Focus C28 y C33 de Clarke son máquinas efectivas y de calidad superior para la limpieza de pisos. El modelo Focus C33 utiliza dos cepillos o almohadillas para limpiar un recorrido de 33 pulgadas de ancho. El modelo Focus C28 utiliza dos cepillos o almohadillas para limpiar un recorrido de 28 pulgadas de ancho. -
Page 27: Especificaciones De La Máquina
Inclinación de 6° Inclinación de 6° Peso con baterías (310AH) 1015 lbs. 460kg 1005 lbs. 456kg Peso de envío 1318 lbs. 598kg 1308 lbs. 593kg con baterías (310AH) Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 27 -... -
Page 28: Procedimientos Para Transporte
9. Vuelva a colocar el montaje de la escobilla de goma, los alojamientos de los cepillos y los cepillos o impulsores de almohadillas una vez que la máquina haya sido descargada y esté lista para usar. Clarke ® -28- Manual del operador (ES) - FOCUS C28 and C33... -
Page 29: Símbolos Utilizados En Los Modelos 24V, C28 / C33
Etiqueta de advertencia (con freno de Cepillo Arriba/ Abajo estacionamiento) Control de solución Etiqueta de advertencia (sin freno de estacionamiento) Alimentación Control de velocidad de desplazamiento Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 29 -... -
Page 30: Panel De Control De La Máquina En Los Modelos 24V, C28 / C33
El cuentavueltas calibrado en horas de trabajo indica el número de horas que ha funcionado la máquina. Sólo funciona cuando la máquina se mueve hacia adelante o hacia atrás. Clarke ® -30- Manual del operador (ES) - FOCUS C28 and C33... - Page 31 ESPAÑOL PANEL DE CONTROL DE LA MÁQUINA C28, C33 Figura 1 Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 31 -...
-
Page 32: Controles Y Funciones De La Máquina
El interruptor de apagado del motor de vacío está ubicado en el depósito de recuperación. Apaga automáticamente el motor de vacío cuando el depósito de recuperación está lleno. Figura #3b Figura #4 Figura #3c Figura #5 Clarke ® -32- Manual del operador (ES) - FOCUS C28 and C33... -
Page 33: Preparación De La Máquina Para El Funcionamiento
ESPAÑOL PREPARACIÓN DE LA MÁQUINA PARA EL FUNCIONAMIENTO Instalación de las baterías Las máquinas Focus C28 y C33 utilizan 4 baterías de 6 voltios. Dichas baterías están situadas en el compartimiento para baterías, debajo del depósito de recuperación. Para instalar las baterías siga este procedimiento: 1. -
Page 34: Mantenimiento De Las Baterías
Para limpiar los bornes y conectores, utilice una herramienta de limpieza para bornes y conectores. No permita que entren en las baterías amoníaco ni bicarbonato. Mantenga las baterías cargadas. Clarke ® -34- Manual del operador (ES) - FOCUS C28 and C33... -
Page 35: Carga De Las Baterías
Cada 20 operaciones de recarga, verifique el nivel de electrolito, y de ser necesario cubra por completo con agua destilada. Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 35 -... -
Page 36: Instalación De Los Cepillos O Los Impulsores De Almohadillas
4. Diríjase a la parte delantera de la máquina. 5. Empuje hacia abajo los dos lados del cepillo o impulsor de almohadillas, hasta que se liberen las suspensiones cardánicas. Clarke ® -36- Manual del operador (ES) - FOCUS C28 and C33... -
Page 37: Operación De La Máquina
16. El nivel de solución puede visualizarse desde la parte posterior de la máquina. Figura Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 37 -... -
Page 38: Desplazamiento De La Máquina
2 pulgadas (5cm) del área ya limpiada. NOTA: Durante la mayoría de los procedimientos de limpieza, aplique y quite la solución en una sola operación. Clarke ® -38- Manual del operador (ES) - FOCUS C28 and C33... -
Page 39: Limpieza De Pisos
7. Asegúrese de que los cepillos estén en posición y se hayan instalado correctamente 8. Verifique la instalación de la escobilla de goma y de la manguera de la misma. Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 39 -... -
Page 40: Mantenimiento
Utilice un trapo limpio y limpie la superficie de la máquina. Cargue las baterías. Consulte las instrucciones incluidas en la sección de este manual llamada “Carga de las baterías”. Clarke ® -40- Manual del operador (ES) - FOCUS C28 and C33... - Page 41 5. Utilice una pistola de grasa para lubricar la rueda propulsora y las roldanas pivotantes. Consulte la figura 25. 6. Controle la presión del neumático. La presión del neumático debe ser de aproximadamente 50 psi. Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 41 -...
- Page 42 Si se cambia la inclinación, puede que sea también necesario realizar ajustes en la presión de la escobilla de goma. Clarke ® -42- Manual del operador (ES) - FOCUS C28 and C33...
- Page 43 (figura 31, B) y limpie o reemplace el tubo de solución. Prenda la válvula de la solución (fiugura 31, A). Vuelva a empujar el montaje de filtro Figura hacia dentro del bastidor. Figura Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 43 -...
-
Page 44: Corrección De Problemas
Verifique la posición de la palanca de transferencia de mando del freno de estacionamiento (si está instalada) NOTA: si el motor sigue deteniéndose, consulte a una persona del servicio técnico autorizado. Clarke ® -44- Manual del operador (ES) - FOCUS C28 and C33... -
Page 45: Accesorios
14" Poly 11427B 14" Grit-Heavy 11426B 14" Grit-Medium 11431B 14" Grit-Lite 10383A 14" Soft Nylon 11429B Impulsores de almohadillas: Tamaño Pieza N°. 17" 17520C 14" 17521C Clarke ® Manual del operador (ES) - FOCUS C28 and C33 - 45 -... - Page 46 La non-lecture de ce manuel avant d’utiliser ou d’entretenir votre machine Clarke risque de provoquer un accident ou d’endommager la machine ou son environnement. Vous devez avoir été formé à l’utilisation de cette machine avant de l’utiliser. Si l’opérateur n’est pas en mesure de lire ce Manuel, il devra se le faire expliquer entièrement avant de...
-
Page 47: Consignes De Sécurité Destinées À L'opérateur
La non-lecture du Manuel de l’utilisateur avant d’utiliser ou de tenter d’entretenir votre machine Clarke est susceptible de provoquer un accident ; un ndommagement de la machine ou de son environnement est également possible. Vous devez avoir été formé à... -
Page 48: Introduction
La Focus C33 utilise deux brosses ou tampons et offre une largeur de nettoyage de 83,82 cm. La Focus C28 utilise deux brosses ou tampons et offre une largeur de nettoyage de 71,12 cm. Une raclette essuie le sol tandis que le moteur d’aspiration enlève la solution sale du sol, le tout simultanément. -
Page 49: Caractéristiques De La Machine
71 cm Grade Cleaning Angle de 6° Angle de 6° Poids Avec batteries(310Ah) 460 kg 456 kg Poids à l’expédition 598 kg 593 kg avec batteries (310Ah) Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 49 -... -
Page 50: Procédures De Transport
9. Remettez en place la raclette, les protections des brosses, les brosses ou les entraîneurs de disque une fois la machine déchargée et prête à être utilisée. Clarke ® -50- Manuel de l’utilisateur (FR) - FOCUS C28 and C33... -
Page 51: Symboles Utilisés Sur 24V, C28 / C33
Commutateur à clé Marche/Arrêt Autocollant d’avertissement Abaissement/relèvement des (avec frein de brosses stationnement) Niveau de solution Autocollant d’avertissement (sans frein de stationnement) Alimentation Contrôle de la vitesse de déplacement Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 51 -... -
Page 52: Panneau De Commandes Des Machines 24V, C28 / C33
« ON », et ré-essayez. Un technicien agréé doit être contacté si le disjoncteur se déclenche de nouveau. Compteur horaire (Cf. Figure 1M) Le compteur horaire indique le nombre d’heures de fonctionnement de la machine. Il ne fonctionne que lorsque la machine avance ou recule. Clarke ® -52- Manuel de l’utilisateur (FR) - FOCUS C28 and C33... - Page 53 FRANÇAIS PANNEAU DE COMMANDE DES MODELES C28, C33 Figure 1 Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 53 -...
-
Page 54: Commandes Et Fonctions De La Machine
Le commutateur d’arrêt du moteur d’aspiration est situé dans le réservoir de récupération. Il éteint automatiquement le moteur d’aspiration lorsque le réservoir de récupération est plein. Figure #3b Figure #4 Figure #3c Figure #5 Clarke ® -54- Manuel de l’utilisateur (FR) - FOCUS C28 and C33... -
Page 55: Préparation De La Machine Avant Son Utilisation
Remettez le dispositif de fixation du réservoir en place. REMARQUE: Charger les batteries avant d’utiliser la machine. Figure #6b Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 55 -... -
Page 56: Entretien Des Batteries
Pour nettoyer les bornes et les connecteurs, utilisez un outil de nettoyage spécifique. Ne laissez pas l’ammoniaque ou le bicarbonate de soude pénétrer dans les batteries. Veillez à ce que les batteries soient chargées. Clarke ® -56- Manuel de l’utilisateur (FR) - FOCUS C28 and C33... -
Page 57: Chargement Des Batteries
Toutes les 20 opérations de recharge, vérifiez le niveau d’électrolyte et complétez, si nécessaire, avec de l’eau distillée. Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 57 -... -
Page 58: Installation Des Brosses Ou Des Entraîneurs De Disque
4. Allez à l’avant de la machine. 5. Poussez les deux côtés de la brosse ou de l’entraîneur de disque vers le bas jusqu’à ce que les axes se libèrent. Clarke ® -58- Manuel de l’utilisateur (FR) - FOCUS C28 and C33... -
Page 59: Utilisation De La Machine
16. Le niveau de solution peut être vérifié depuis l’arrière de la machine. Figure #16 Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 59 -... -
Page 60: Conduite De La Machine
5 cm. REMARQUE : Lors de la plupart des opérations de nettoyage, vous appliquerez et retirerez la solution en une seule et même opération. Clarke ® -60- Manuel de l’utilisateur (FR) - FOCUS C28 and C33... -
Page 61: Maintenance
7. Asegúrese de que los cepillos estén en posición y se hayan instalado correctamente 8. Verifique la instalación de la escobilla de goma y de la manguera de la misma. Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 61 -... - Page 62 Utilisez un chiffon propre pour essuyer la surface de la machine. Chargez les batteries. Consutez les instructions données dans la section de ce Manuel intitulée « Rechargement de la batterie ». Clarke ® -62- Manuel de l’utilisateur (FR) - FOCUS C28 and C33...
- Page 63 5. Utilisez un pistolet graisseur pour lubrifier la roue d’entraînement et les galets pivotants. Cf. figure 25. 6. Vérifiez la pression des pneus. Celle-ci doit être d’environ 50 psi. Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 63 -...
- Page 64 “Y” vers le haut. Procédez par très petits ajustements et continuez jusqu’à ce qu’une déformation uniforme soit atteinte. La modification de l’inclinaison peut nécessiter un réglage de la pression exercée sur la raclette. Clarke ® -64- Manuel de l’utilisateur (FR) - FOCUS C28 and C33...
- Page 65 (figure 31, B). Nettoyez-le ou remplacez-le. Allumer la soupape de solution (figure 31, A). Replacez le filtre dans son emplacement. Figure #30 Figure #31 Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 65 -...
-
Page 66: Résolution Des Problèmes
Vérifiez les connexions de la batterie. Vérifiez la position du levier du frein de stationnement (s’il est installé) REMARQUE : si le moteur continue à s’arrêter, consultez un technicien agréé. Clarke ® -66- Manuel de l’utilisateur (FR) - FOCUS C28 and C33... -
Page 67: Accessoires
11 426B 14" Grit-Medium 11 431B 14" Grit-Lite 10 383A 14" Soft Nylon 11 429B Entraîneurs de disque : Taille N° de pièce 17" 17520C 14" 17521C Clarke ® Manuel de l’utilisateur (FR) - FOCUS C28 and C33 - 67 -... - Page 68 NOTES ® Clarke Page -68- Operator's Manual - FOCUS C28 and C33...
-
Page 69: Section Ii Parts And Service Manual
24V Models C28 and C33 Section II Parts and Service Manual (70951A) U.S. Patent No. 6,760,947; No. 6,105,192; No. 6,493,896 (Deluxe Machines); & Patent Pending Clarke ® Operator's Manual - FOCUS C28 and C33 - 69 -... -
Page 70: Solution Tank Assembly
® Clarke FOCUS C28 and C33 Solution Tank Assembly Drawing 11/06 33 34 ® Clarke Page -70- Operator's Manual - FOCUS C28 and C33... -
Page 71: Parts List
Clamp, Hose 81109A Nut, 8-32 S.S. Elastic Lock 54088A Valve, Shut-Off 40512A Battery Charger NOTE: indicates a change has been made since the last publication of this manual. Clarke ® Operator's Manual - FOCUS C28 and C33 - 71 -... -
Page 72: Recovery Tank Assembly
® Clarke FOCUS C28 and C33 Recovery Tank Assembly Drawing 7/07 Form # 10983A 16, 16A ® Clarke Page -72- Operator's Manual - FOCUS C28 and C33... -
Page 73: Parts List
Hinge Pin (included with item #36) 30591A Recovery Tank 40002A Float Switch (includes items, #38 & 2 ea. #11& #12) 56459A Strain Relief (included in item #37) 87612A Seal Clarke ® Operator's Manual - FOCUS C28 and C33 - 73 -... -
Page 74: Electrical Panel Assembly
® Clarke FOCUS C28 and C33 Electrical Panel Assembly Drawing 2/07 Form # 10985A ® Clarke Page -74- Operator's Manual - FOCUS C28 and C33... -
Page 75: Parts List
Squeegee Knob 980666 Washer, 3/8 External 85389A Screw, 3/8-16 x 5/8 68643A Wear Plate 980675 Washer 962546 Screw, 10-24 x 1/2 47388A Switch 54436A Plug, Hole 1 3/8 Clarke ® Operator's Manual - FOCUS C28 and C33 - 75 -... -
Page 76: Control Panel Assembly
Clarke ® FOCUS C28 and C33 Control Panel Assembly Drawing 10/07 Form # 10985A ® Clarke Page -76- Operator's Manual - FOCUS C28 and C33... -
Page 77: Parts List
Panel, Control (used w/key switch 18A) 61747B Panel, Conrol (used w/key switch 18B) 41448B Circuit, Breaker, 30A 41422B Circuit, Breaker, 25A 44308B Solution Modulator 920296 Nut, Lk 10-24 40898A Meter, Battery/Charger Clarke ® Operator's Manual - FOCUS C28 and C33 - 77 -... -
Page 78: Squeegee Swing Arm Assembly
® Clarke FOCUS C28 and C33 Squeegee Swing Arm Assembly Drawing 11/07 ® Clarke Page -78- Operator's Manual - FOCUS C28 and C33... -
Page 79: Parts List
NOTE: When changing squeegee blades, it might be necessary to loosen screw #52; install and secure blades with clamp #47; then retighten screw #52. This will allow for different thickness. Clarke ® Operator's Manual - FOCUS C28 and C33 - 79 -... -
Page 80: Traverse System Assembly
® Clarke FOCUS C28 and C33 Traverse System Assembly Drawing 3/05 Form # 10984A ® Clarke Page -80- Operator's Manual - FOCUS C28 and C33... -
Page 81: Parts List
58419A Stud, 980205 Washer, .25 Fender 69639A Strap, Static 980645 Washer, Flat 962244 Screw, -16 x ¾ 980638 Lockwasher *30039A tube, inner (included in item #16) 1 Ref. Clarke ® Operator's Manual - FOCUS C28 and C33 - 81 -... -
Page 82: Brush Head Assembly
Clarke ® FOCUS C28 and C33 Brush Head Assembly Drawing 5/05 Form # 10986A & # 10987A ® Clarke Page -82- Operator's Manual - FOCUS C28 and C33... -
Page 83: Parts List
77091A Label, Moving Parts 980638 Washer, Lock .375 *Used only as required to square up linkage bars #9 to the frame. **Attach to Brush Motor. ***Includes Item #11 Clarke ® Operator's Manual - FOCUS C28 and C33 - 83 -... -
Page 84: Brush Motor Assembly
® Clarke FOCUS C28 and C33 Brush Motor #44809B 3/05 Seam Location ® Clarke Page -84- Operator's Manual - FOCUS C28 and C33... -
Page 85: Parts List
55657A Lead Assembly 55656A Lead Assembly Helical Washer 50515A Thru Bolt 80501A Shaft Key 54238A B.E. Bracket Assembly (Gear Box) * NOTE: Parts not available at this time. Clarke ® Operator's Manual - FOCUS C28 and C33 - 85 -... -
Page 86: Gearbox
507641 Seal, Oil, Small 52050A Cap End 56668A O'Ring 51176A Bearing, Large 58316A Shaft & Gear, Gearbox 902605 Bearing, Small 54883A Housing 58144A Seal, Oil Large Darina Grease 4oz. ® Clarke Page -86- Operator's Manual - FOCUS C28 and C33... -
Page 87: Imperial Transaxle Parts 11/05
Clarke ® FOCUS C28 and C33 Imperial Transaxle Parts 11/05 Clarke ® Operator's Manual - FOCUS C28 and C33 - 87 -... -
Page 88: Control Panel Connection Diagram 5/05
Clarke ® FOCUS C28 and C33 Control Panel Connection Diagram 5/05 ® Clarke FOCUS 24V28 and 24V33 (Front of Machine) Connection Diagram 2/05 ® Clarke Page -88- Operator's Manual - FOCUS C28 and C33... -
Page 89: Electrical Plate Connection Diagram 11/06
Clarke ® FOCUS C28 and C33 Electrical Plate Connection Diagram 11/06 Clarke ® Operator's Manual - FOCUS C28 and C33 - 89 -... -
Page 90: Control Housing Connection Diagram 3/05
Clarke ® FOCUS C28 and C33 Control Housing Connection Diagram 3/05 ® Clarke Page -90- Operator's Manual - FOCUS C28 and C33... -
Page 91: Electrical Schematic 11/06
® Clarke FOCUS C28 and C33 Electrical Schematic 11/06 Clarke ® Operator's Manual - FOCUS C28 and C33 - 91 -... - Page 92 NOTES...
- Page 93 29815 John R. +49 0180 5 37 37 37 (810) 544-6300 ALTO Cleaning Systems (UK) Ltd., Penrith American Lincoln ® / Clarke, Marietta, Georgia 30066 Gilwilly Industrial Estate 1455 Canton Road Penrith (770) 218-2116 Cumbria CA11 9BN +44 1768 868 995 ALTO France S.A.
- Page 94 STATED WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED Clarke's liability under this warranty is limited to repair of the product and/or replacement of parts and is given to purchaser in lieu of all other remedies, including INCIDENTAL AND CONSEQUENTIAL DAMAGES.