Viper 5104 1-Way Owner's Manual
  1. Manuals
  2. Brands
  3. Viper Manuals
  4. Car Alarm
  5. 5104 1-Way
  6. Owner's manual

Viper 5104 1-Way Owner's Manual

Car security system and remote start
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Viper 5104 1-Way

Summary of Contents for Viper 5104 1-Way

  • Page 2: What You Get

    Reading this Owner’s Guide prior to using your system will help maximize the use of your system and its many fea- tures. Please visit the below website: http://www.viper.com – For general and additional guide information. For any additional ques- tions please contact your authorized Directed dealer or contact Di- rected at 1-800-753-0600.

  • Page 3: Important Information

    Important information Government Regulations and Safety information Read the Government Regulations and Warning! Safety First sections of this manual prior to operating this system. Warning! Failure to heed this information can result in death, personal injury or property damage and may also result in the illegal use of the system beyond its intended purpose.

  • Page 4: Table Of Contents

    Contents Getting Started ....................3 Keys to using this manual ..............3 Remote Control ....................4 Using your System ....................6 Commanding the system ............... 6 Performing Commands ................. 6 Remote Control Command table ............7 Basic Commands (Direct Access) ................8 Arm ....................
  • Page 5 Nuisance Prevention (NPC) ..............20 Remote Start Features ..................21 Pit Stop Mode ................... 21 Key Takeover..................21 Remote Start Safe-lock ................ 22 Disabling Remote Start ............... 22 Advanced Start ................. 22 Manual Transmission Start (MTS mode) ..........23 Turbo Timer Mode ................24 Remote Start Faults ................

  • Page 6: Getting Started

    Getting Started Keys to using this manual Specific actions (in bold type) and style conventions are used consis- tently throughout this manual, they are as follows: Press: implies pushing in and releasing a button. Hold: is used after Press actions when a button needs to be held in position for an extended period of time, typically several sec- onds.

  • Page 7: Remote Control

    Remote Control Internal Antenna Transmit Command Buttons Function Button Feature Description Internal Antenna Used for transmitting information Transmit LED Active when transmitting information Command buttons (4) Used to perform arming, disarming, auxiliary channel and remote start commands Function button Used to access function levels for commands, configuration menus for programming and Car Selection ©...
  • Page 8 Control Center Control button Antenna Status LED The Control Center, typically located on the upper part of the front windshield. It consists of: The In-vehicle system antenna. The Status LED, as a visual indicator of the system’s status. The Control button, for placing the system into Valet Mode* and to perform the Emergency Override** operation.

  • Page 9: Using Your System

    Using your System Commanding the system Commands, Basic or Advanced, are used to activate system features and are performed by pressing one of the Command buttons. Basic commands control the most often used security and remote start fea- tures while Advanced commands control more specialized features. Confirmations for Basic or Advanced commands are indicated by siren chirps and parking light flashes.

  • Page 10: Remote Control Command Table

    Remote Control Command table Direct Access Level Button LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 Arm/Lock Silent Arm Sensor Sensor Silent Full Silent (Panic) Bypass Disarm/Unlock Silent Disarm Remote Valet Car Finder Remote Start Runtime Timer Start Smart Start Defogger Reset Aux/Trunk...

  • Page 11: Basic Commands (Direct Access)

    Basic Commands (Direct Access) Press and release The alarm arms, doors lock (if connected), and the siren chirps and parking lights flash once. If Valet mode* is On, the doors lock without siren chirps, the alarm is disabled. Exit Valet mode to arm the alarm normally.

  • Page 12: Remote Start

    Remote Start Press and release Activates (or if On, deactivates) the remote starter. The engine and parking lights turn On, or the engine and parking lights turn Off ac- cordingly. If a Remote start configuration issue prevents the engine from starting, the parking lights flash a Remote Start fault report*** to identify the fault.

  • Page 13: Advanced Commands: (Level 1)

    Advanced Commands: (Level 1) Press and release the button 1 time. The transmit LED illuminates in sets of single flashes to indicate Level 1. Silent Arm Press and release The alarm arms, doors lock (if connected), and the parking lights flash once.

  • Page 14: Advanced Commands: (Level 2)

    Advanced Commands: (Level 2) Press and release the button 2 times. The transmit LED illuminates in sets of double flashes to indicate Level 2. Sensor Bypass Press and release Performing the Sensor Bypass command will incrementally bypass sen- sor operations and be confirmed as follows: Warn-away bypass: The Parking lights flash 2 times.

  • Page 15: Timer Start

    Timer Start* Press and release Activates (or if On, deactivates) Timer Start. The parking lights flash quickly four times for On and slowly four times for Off. Note System needs to be armed or Timer Start will not start the engine.

  • Page 16: Advanced Commands: (Level 3)

    Advanced Commands: (Level 3) Press and release the button 3 times. The transmit LED illuminates in sets of triple flashes to indicate Level 3. Sensor Silent Arm* Press and release The alarm arms, doors lock, and the siren chirps and parking lights flash 3 times.

  • Page 17: Advanced Commands: (Level 4)

    Advanced Commands: (Level 4) Press and release the button 4 times. The transmit LED illuminates in sets of quadruple flashes to indicate Level 4. Full Silent Arm* Press and release The alarm arms, doors lock, and the siren chirps and parking lights flash 4 times.

  • Page 18: Remote Control Configuration

    Remote Control Configuration Remote Programming The remote controls have operations that can be configured to a user’s personal preferences. The following instruction will direct you through the available programming options for both remote controls. Enter programming, press and hold the button for 8 seconds, the transmit LED turns on to indicate the Main Menu is accessed.

  • Page 19: Remote Features

    Prepare the remote control for pairing: Enter programming to access the Main Menu Press and hold the button for 1 second, 3 transmit LED flash- es indicate the remote control is ready to pair. Press the button, The siren will chirp to confirm the system has learned the remote con- trol.

  • Page 20: Sensor Adjust

    To unlock the buttons, press the button followed by the button. Note When the Keypad is locked, the remote control may ap- pear to be non-operational. It will not transmit a command or illuminate the Transmit LED and needs to be unlocked to resume normal operation.

  • Page 21: Alarm Features

    Alarm Features Normal Arm Protection Status LED: The Control Center Status LED flashes as a visual indicator that your vehicle’s security system is active. Starter Kill: The Failsafe starter kill relay prevents the engine from starting Note May require additional parts and installation Sensor triggers: The onboard shock sensor can distinguish minor im- pacts from major impacts to the vehicle exterior.

  • Page 22: Sensor Warn-Away Output

    Sensor Warn-away output When the system sensors detect a Warn-away trigger the siren chirps and parking lights flash for 3 seconds. Full Trigger output An alarm Full Trigger will sound the siren and flash the parking lights for 30 seconds. Emergency Override The following procedure disarms the system when a programmed re- mote is not available.

  • Page 23: Alarm Report

    Alarm Report If the alarm was triggered while armed, it will be reported when the alarm is disarmed via siren chirps, parking light and control center LED flashes. The siren chirps 4 times (or 5 times if NPC On*), the park- ing lights flash 3 times, and the control center LED flashes in groups to indicate the last two zones that were triggered (see Table of Zones).

  • Page 24: Remote Start Features

    Remote Start Features Pit Stop Mode To exit vehicle with engine running The system keeps the engine running during short trips into the house or convenience store. To perform Pit Stop: With the engine running, set the parking brake and release the foot brake.

  • Page 25: Remote Start Safe-Lock

    Remote Start Safe-lock Remote start safe-lock makes sure the doors are locked while the en- gine is running and after, even if they are unlocked when remote start is activated. Door locks may require additional parts and labor. Disabling Remote Start Remote start can be disabled by moving the Toggle Switch to the Off position.

  • Page 26: Manual Transmission Start (Mts Mode)

    by the installer (default 6 starts). Timer Start is exited after the final start. Smart Start operation Smart Start uses the settings for Timer Start in addition to tempera- ture and battery level to automatically start the engine. Activation begins the countdown timer. When the timer expires the vehicle interior temperature and battery level is checked and, if the Tem- perature is above 100F, below 0F, or the battery level is be- low 10.5v, the engine will start.

  • Page 27: Turbo Timer Mode

    button on the remote, after 20 seconds return to Step 2 (For Turbo Timer Mode, press the optional dash mounted activation button or send the Timer Mode command. The parking lights flash 5 times to confirm MTS mode is enabled and the remote start activates the ignition outputs.

  • Page 28: Remote Start Faults

    Remote Start Faults For user safety, the system must be properly configured or remote start will not activate. A Remote Start Fault may be caused by any of several configuration issues. Refer to the table below for the command type and parking light flashes that will identify the configuration issue and solution.

  • Page 29: Remote And System Operations

    Remote and System Operations Passive Arming* Park and exit the vehicle, after the doors are closed the Passive arm- ing countdown begins. The led flashes quickly and upon reaching 20 seconds the siren then chirps once. At 30 seconds the system arms itself.

  • Page 30: Valet Mode

    Valet Mode Valet mode can be entered and exited by performing the Remote Valet command or manually using the vehicle key and the control button. When entered, the alarm functions are defeated while the conve- nience features still operate normally. Use the following steps to manually enter and exit Valet Mode: Turn the ignition switch On and then Off Immediately press and release the control button once...

  • Page 31: System Expansion Options

    System Expansion Options Controlling two vehicles (Car Select) The remote controls can control systems in two different vehicles sav- ing the need for multiple remote controls. This feature also allows for customized system configurations on each vehicle that has more than one driver.

  • Page 32: Battery Information

    Battery Information The remote controls are powered by 1 coin cell battery (CR-2032) that can be purchased at most retailers. When the battery begins to weaken, the operating range will be reduced. The information and precautions in this section can help maximize your battery’s life and usage in providing you with many years of trouble free operation.

  • Page 33: Battery Disposal

    Directed Electronics at: One Viper way, Vista, CA 92081 (Shipping and/or handling costs are the sole responsibility of the owner/sender and will not be covered by Directed Electronics).

  • Page 34: Glossary Of Terms

    Glossary of Terms Document Terminology Control Module The “brain” of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all of the system’s func- tions. Remote Control A hand-held, remote control which operates the various func- tions of your system.

  • Page 35: Government Regulations

    Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.

  • Page 36: Warning! Safety First

    Warning! Safety First Please read the safety warnings below before proceeding. Improper use of the product may be dangerous or illegal. Installation Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. If you have any questions, ask your retailer or contact Directed directly at 1-800-753-0600.
  • Page 37 Before remote starting a manual transmission vehicle, be sure to: Leave the vehicle in neutral and be sure no one is standing in front or behind the vehicle. Only remote start on a flat surface Have the parking brake fully engaged WARNING! It is the responsibility of the owner to ensure the parking/emer- gency brake properly functions.

  • Page 38: Interference

    GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPER- ATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMME- DIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE.

  • Page 39: Limited Lifetime Consumer Warranty

    Limited lifetime consumer warranty Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at Directed’s election) with a comparable reconditioned model any Directed unit (hereaf- ter the “unit”), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was purchased from an authorized Directed dealer, the unit was professionally...
  • Page 40 ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT.

Table of Contents