VTech LS6475-2 Quick Start Manual

®
Quick start guide
LS6475-2/LS6475-3/LS6476-4
Introduction
This quick start guide provides you with the basic installation
and use instructions. A limited set of features are described in
abbreviated form.
Please refer to the user's manual for complete installation and
.
operation instructions
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone base Telephone
Electrical outlet
power adapter wall jack
not controlled
by a wall switch
If you have
Electrical DSL high
outlet not speed Internet
controlled by
service, a
a wall switch
DSL filter (not
included) is
required.
Telephone
line cord
Telephone base
Handset battery installation and charging
Install the battery as shown below. Once you have installed the battery,
you may be able to make and receive short calls. For best performance,
charge the handset battery continuously for at least 10 hours.
2. Place the battery with the
1. Plug the battery connector
securely into the socket label THIS SIDE UP facing
inside the handset battery up and the wires inside the
compartment, matching the battery compartment.
color-coded label.
3. Slide the battery compartment 4. Place the handset in the
cover towards the center of the telephone base or charger
handset until it clicks into place. to charge.
CHARGE light
remains on when
charging.
Headset charging
After installing the telephone base, charge the headset as shown
below. The headset is fully charged after three hours of continuous
charging. If the light does not turn on while charging, you need
to charge the headset without interruption for at least 15 minutes to
give the headset enough charge to use for a short time.
1. Place the tip of the headset in the small cradle on the
telephone base.
Charger
adapter
2. The magnet holds the top of the headset in place. The
turns on when charging.
Charger Telephone base overview
IN USE light
Flashes when there is an
incoming call, or another
telephone sharing the
X/DELETE
same line is in use.
Delete the message currently playing.
Flashes when the
Press twice to delete all old messages
handsets/headsets are
when the telephone is not in use.
being deregistered.
On when the phone is
in use, or the answering
system is answering a call.
On when a handset/
headset is being
registered.
/FIND HANDSET
Page all handsets
and the headset.
/REPEAT
Repeat a message or press
twice to play the previous
message.
Handset overview
CHARGE light
On when the handset is
charging.
/ /VOLUME
Review the directory
when the telephone is not
in use.
Scroll up while in a menu.
Increase the listening
volume during a call or
message playback.
Move the cursor to the
right when entering
numbers or names in the
directory.
MUTE/DELETE
Mute the microphone
during a call.
Delete the displayed entry
while in the directory,
caller ID log or redial list.
Silence the ringer
temporarily while the
handset is ringing.
Delete digits or characters
light
while using the dialing keys.
/FLASH
Make or answer a call.
Answer a call waiting call
The light
during a call.
1
Press repeatedly to add
or remove 1 in front of the
caller ID log entry before
dialing or saving it to the
directory.
Switch to tone dialing
temporarily while on a call.
/ SPEAKER
Make or answer a call using the
handset speakerphone.
Switch between the speakerphone
and the handset during a call.
REDIAL/PAUSE
Review the redial list.
Press and hold to insert a dialing pause
while dialing or entering numbers in the
Message window
directory.
Shows the number
of messages and
Headset overview
other answering
system information.
/VOL/
Adjust the
base ringer
volume or
the speaker
volume. Rotating clip
+/-/VOLUME
Connect the
Adjust the
ear hook or
listening volume
/SKIP
head band.
while on a call.
Skip to the next
RESET inset
Adjust the
message.
button
ringer volume
/ANS ON/OFF
when the
Insert a paper
headset is not
Turn the answering clip or similar
in use.
system on or off. object to reset
the headset when
/PLAY/STOP
deregistration fails.
Play massages or stop
message playback.
Using the menu
CID/ /VOLUME
To enter the handset menu:
Review the caller ID log when
1. Press MENU/
the telephone is not in use.
2. Press or
Scroll down while in a menu.
Decrease the listening volume 3. Press
MENU/
during a call or message
• To return to the previous menu, press
playback.
• To return to idle mode, press and hold
Move the cursor to the left when
entering numbers or names in
the directory.
Telephone settings
MENU/SELECT Default settings are indicated by asterisks (*).
Show the menu.
Screen display
Choose an item, or save an
entry or setting while in a menu.
LCD language
PUSH TO TALK (PTT)
Begin a one-to-one or
Annc Caller ID
one-to-group broadcast.
OFF/CANCEL
Hang up a call.
Clr voicemail
Silence the ringer
temporarily while the
Rename handset Change the name of each
handset is ringing.
Press and hold to delete
Key tone
the missed call indicator
while the telephone is
not in use.
CID time sync
Press to return to the
previous menu, or
Home area code
press and hold to return
to idle mode without
making changes.
Dial mode
Dialing keys
Enter numbers or
characters.
Set date and time
# (pound key) Press MENU/
1.
Press repeatedly to
Scroll to >Set date/time, then press
2.
show other dialing
3. Press
options when reviewing
a caller ID log entry.
-OR-
Switch the name order
Use the dialing keys (0-9) to enter the current month.
when saving the caller
4. Repeat Step 3 to set the correct date and year and then press
ID log entries to the
directory.
SELECT to advance to set the time.
MENU/
5. Repeat Step 3 until the time is set. Press
EQ
PM, or press 2 for AM or 7 for PM.
Change the audio quality to
best suit your hearing during
6. Press
MENU
an outside call, intercom call,
message or announcement
Ringer volume (telephone base)
playback.
Press /VOL or /VOL on the side of the telephone base to adjust
•
the ringer volume when the telephone is not in use.
(on/off) Ringer volume (handset)
Press and hold two seconds 1. Press MENU/
to power on or off.
2. Scroll to >Ringers, then press
Earpiece
Answer, end or join a call.
3. Press
MENU
4. Press
/SELECT to save your selection.
MENU
Ringer volume (headset)
Press +/-/VOLUME on the side of the headset when it is not in use.
Telephone operation
MUTE/FLASH
Make a call
Mute the microphone while
on a call. 1. Press
/FLASH
Press and hold to answer 2. Press on the headset to join the call.
an incoming call when you
-OR-
receive a call waiting alert
1. Predial by first dialing the telephone number and then press
during a call.
/FLASH
Silence the ringer in the
2. Press on the headset to join the call.
earpiece temporarily when
the headset is ringing.
Microphone
when the telephone is not in use.
SELECT
until the screen displays the desired feature menu.
SELECT to enter that menu.
/CANCEL.
OFF
/CANCEL.
OFF
Function Options
Set the screen display language. English*
Français
Espaňol
On*
Enable the telephone base and/or
the handset to announce the Off
incoming caller ID information.
Turn off
Turn off the
voicemail indicators. indicator?
HANDSET____
registered handset.
Adjust the key tone volume whenever *
a key is pressed, or turn it off.
Off
Enable the date and time to be set On*
by incoming caller ID information. Off
_ _ _
Enter your home area code if you dial
only seven digits for local calls.
Set the telephone to be tone or Tone*
pulse dialing. Pulse
when the handset is not in use.
SELECT
/SELECT.
MENU
SELECT.
or to set the month, then press
MENU/
or to select AM or
/SELECT to save.
when the handset is not in use.
SELECT
/SELECT.
MENU
/SELECT to select >Ringer volume.
or to sample each volume level, then press
or /SPEAKER, then dial the telephone number.
or /SPEAKER.