Page 1
® User’s manual Accessory handset for use with VTech models LS6425/LS6426/ LS6475/LS6476 w w w.v t e c h p h o n e s . c o m Model: LS6405...
Page 2
The ENERGY STAR encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR label indicating it meets the latest energy efficiency guidelines. Telephones identified with this logo have reduced noise and interference Compatible with Hearing Aid T-Coil when used with most T-coil equipped hearing aids and cochlear implants.
1 (800) 267-7377. Battery compartment cover ® User’s manual Accessory handset for use with VTech models LS6425/LS6426/ LS6475/LS6476 w w w.v t e c h p h o n e s . c o m Model: LS6405 User’s manual...
Getting started Battery installation Install the battery as shown below. Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label. Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment.
Getting started Battery charging Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use.
Getting started Add and register a handset You can add new handsets (LS6405, purchased separately) to your telephone system. Each handset must be registered with the telephone base before use. When first purchased, each handset displays Put HS on BASE to register. You may need to charge the handset before registering it to the telephone base.
Getting started Deregister handsets If you want to replace a handset, or reassign the designated handset number of a registered handset, you must deregister all handsets that are registered to the telephone base. Then register each handset individually. To make deregistration easier, read all of the instructions on this page before you begin.
Getting started Handset layout CHARGE light On when the handset is charging in the telephone base or charger. / /VOLUME (directory/volume) Press to enter the directory when the telephone is not in use. While in a menu, press to scroll up. During a call or message playback, press to increase the listening volume.
Page 10
Getting started Handset layout CID/ /VOLUME (caller ID/volume) Press to review the caller ID log when the telephone is not in use. While in a menu, press to scroll down. During a call or message playback, press to decrease the listening volume. When entering numbers or names in the directory, press to move the cursor to the left.
Page 11
Getting started Handset layout PUSH TO TALK (PTT) Press to begin a broadcast to one or multiple handsets. Press and hold to broadcast to a group of handsets when the handset is not in use.
Appendix Battery It takes up to 10 hours for the battery to be fully charged. When it is fully charged, you can expect the following performance: Operation While in handset use (talking*) While in speakerphone mode (talking*) While not in use (standby**) *Operating times vary depending on your actual use and the age of the battery.
Appendix Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning.
Appendix Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S.
VTech product service centers. Please call ® 1 (800) 8 BATTERY for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources. ® RBRC is a registered trademark of Rechargeable Battery Recycling Corporation.
Appendix FCC, ACTA and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation.
Appendix FCC, ACTA and IC regulations If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited warranty. If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue your telephone service.
What does this limited warranty cover? The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions.
Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity.
Appendix Technical specifications Frequency Control Crystal controlled PLL synthesizer Transmit frequency Handset: 1921.536-1928.448 MHz Telephone base: 1921.536-1928.448 MHz Channels Nominal effective Maximum power allowed by FCC and IC. Actual operating range may vary range according to environmental conditions at the time of use. Power requirements Handset: 2.4V Ni-MH battery Handset charger: 6V AC @ 300mA...