Accessories; Optional Field Installed Accessories - Lincoln Electric VANTAGE 520 SD Operator's Manual

VANTAGE ® 520 SD

ACCESSORIES

OPTIONAL FIELD INSTALLED ACCESSORIES

K802N POWER PLUG KIT - Provides four 120V plugs rated at 20 amps each and
one dual voltage, full KVA plug rated at 120/240V, 50 amps. 120V plug may not
be compatible with NEMA common household receptacles.
K857 25 ft. (7.5 m) or K857-1 100 ft. (30.4 m) REMOTE CONTROL -
Portable control provides same dial range as the output control on the welder
from a location up to the specified length from the welder. Has convenient
plug for easy connection to the welder. The VANTAGE
equipped with a 12-pin connector for connecting the remote control and 12-
pin to 6-pin adapter.
K704 ACCESSORY SET - Includes 35 feet (10 m) of electrode
cable and 30ft. (9m) of work cable, headshield, Filter plate, work
clamp and electrode holder. Cable is rated at 500 amps, 60% duty
cycle.
K2641-2 FOUR WHEELED STEERABLE YARD TRAILER
For in plant and yard towing. Comes standard with a Duo-Hitch™, a 2"
Ball and Lunette Eye combination hitch.
MEDIUM WELDER TRAILER
For heavy-duty road, off-road, plant and yard use. Includes pivoting jack
stand, safety chains, and 13 in. (330 mm) wheels. Stiff .120 in. (3.0 mm)
welded rectangular steel tube frame construction is phosphate etched and
powder coat painted for superior rust and corrosion resistance. Low sway
suspension gives outstanding stability with manageable tongue weight.
Wheel bearings are packed with high viscosity, high pressure, low washout
Lubriplate ® grease. Includes a Duo-Hitch
Eye combination hitch. Overall width 60 in. (1524 mm). Overall length 124
in. (3150 mm).
K2636-1 Trailer
K2639-1 Fender & Light Kit
K2640-1 Cable Rack
POLARITY/MULTI-PROCESS SWITCH
For easy polarity switching. Example: DC-stick root pass on pipe and DC+
stick for hot, fill and cap passes. Also for an easy process change.
Example: DC+ stick root pass on pipe and DC- Innershield
flux-cored wire for hot, fill and cap passes. 6 and 14-pin remote connec-
tions can be made to this unit. For all Lincoln Electric Chopper Technology
engine-driven welders. Mounts on roof with K2663-1 Docking Kit.
K2642-1
K1816-1 Full KVA Adapter Kit - Plugs into the 120/240V NEMA
14-50R receptacle on the case front (which accepts 4-prong
plugs) and converts it to a NEMA 6-50R receptacle (which accepts
3-prong plugs) for connection to Lincoln Equipment with a NEMA
6-50P plug,
T12153-9 Full-KVA Power Plug - One dual voltage plug rated at
120/240V, 50 amps, single phase.
®
520 SD is
® – a 2 in. (51 mm) Ball/Lunette
® self-shielded
®
Pipe Thawing with an arc welder can cause fire, explosion,
damage to electric wiring or to the arc welder if done improp-
erly. The use of an arc welder for pipe thawing is not
approved by the CSA, nor is it recommended or supported by
Lincoln Electric.
------------------------------------------------------------------
REMOTE OUTPUT CONTROL WITH 120V AC RECEPTACLES
Remote weld output control box with two 120V AC receptacles
having GFCI (Ground Fault Circuit Interrupter) protection. One cord
for both remote and power. 100 ft. (30.5 m) length. Permits
remote adjustment of weld output and power for tools (such as a
grinder) at the work. 20 amp capacity.
K2627-2
DOCKING KIT
Secures the K2642-1 Polarity/Multi- Process Switch to the engine-
driven welder roof. Release latch permits removal of K2642-1
Polarity/Multi- Process Switch. Made from stainless steel for rust-
free operation. For all Lincoln Electric Chopper Technology
engine-driven welders.
K2663-1
TIG OPTIONS
K1783-9 PTA-26V TIG Torch
Air Cooled 200 amp torch (2 piece) equipped with valve for gas
flow control. 25 ft. (7.6m) length.
K870 Foot Amptrol ® - Varies current while welding for making
critical TIG welds and crater filling. Depress pedal to increase cur-
rent. Depressing pedal fully achieves maximum set current. Fully
raising the pedal finishes the weld and starts the after flow cycle
on systems so equipped. Includes 25 ft. (7.6m) control cable.
K963-3 Hand Amptrol ® - Provides 25 ft. (7.6 m) of remote current
control for TIG welding. (6-pin plug connection). Velcro straps
secure torch. (one size fits all Pro-Torch™ TIG Torches)
C-1
ACCESSORIES
WARNING
®