Sound Setting; Bass Level/Mid Level/Treble Level/Balance (Between Left And Right)/Fader (Between Front And Rear)/Loudness/Defeat; Audio Setup; Equalizer Presets - Alpine UTE-80B Owner's Manual

Sound Setting

AUDIO/SETUP
Rotary encoder

/ENTER
BASS
Bass Level/Mid Level/Treble Level/Balance
(Between Left and Right)/Fader (Between
Front and Rear)/Loudness/Defeat
1
Press AUDIOSETUP repeatedly to choose the desired
mode.
Each press changes the mode as follows:
*1/*2
 MID LEVEL
BASS LEVEL
BALANCE  FADER  LOUDNESS
VOLUME  BASS LEVEL
*1 Adjustable only when DEFEAT is OFF.
*2 Not displayed when BASS ENGINE SQ mode is on. (Page 9)
Bass level
Mid level
Treble level
Balance
Fader
Loudness
Defeat
Volume
Note
• If no operation is performed for 5 seconds, the unit automatically
returns to normal mode.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS,
MID, TRE LEVEL and LOUDNESS will return to the factory
defaults.
8
-EN
*1/*2 *1/*2
 TRE LEVEL 
*1/*2
 DEFEAT 
−7 ~ +7
−7 ~ +7
−7 ~ +7
L15 ~ R15
R15 ~ F15
ON/OFF
ON/OFF
0 ~ 35

Audio Setup

You can flexibly customize the unit to suit your own preference and
usage. From the AUDIO SETUP menu, Audio Setting can be modified.
Use steps 1 to 5 to select one of the setting modes to modify.
See the applicable section below for details about the
selected setting item.
1
Press and hold AUDIOSETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select AUDIO, and then press
ENTER.
Note
• When BASS ENGINE SQ setting is set to OFF (MANUAL SET)
(page 9), you can also activate the Audio Setup mode directly by
pressing BASS.
3
Turn the Rotary encoder to select the desired sound
setting menu, and then press ENTER.
*1/*3/*4
 BASS ENGIN
EQ PRESETS
*1/*3/*4/*5
 SOURCE VOL  EQ PRESETS
3BAND EQ
(e.g. Select LOUDNESS)
*1 Adjustment cannot be performed when DEFEAT is set to ON.
*2 Not displayed when the Audio Setup mode is activated by
pressing BASS in MANUAL SET mode (page 10).
*3 These items are set uniformly in BASS ENGINE SQ mode by
adjusting BASS ENGINE SQ Level (page 10) and cannot be
adjusted separately. If you want to change these settings
separately, a message is displayed asking you to confirm that you
want to exit the BASS ENGINE SQ mode. Select "YES" to make
the setting.
*4 Any changes made to either EQ PRESETS or 3BAND EQ are
reflected in the other's settings.
*5 In step 3, three sound adjustment items (Bass, Mid and Treble)
can be selected in 3BAND EQ mode. Turn the Rotary encoder
to select the desired item, and then press ENTER to continue
to step 4.
4
Turn the Rotary encoder to change the setting, and then
press ENTER.
(e.g. Select LOUD ON or LOUD OFF)
5
Press and hold AUDIOSETUP for at least 2 seconds to
return to normal mode.
Notes
• Pressing r returns to the previous Sound menu mode.
• Pressing and holding r for at least 2 seconds will return to normal
mode.
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.

Equalizer Presets

10 typical equalizer settings are preset at the factory for a variety of
musical source material. USER settings are created in the 3BAND EQ
mode.
 Setting item: EQ PRESETS
Setting contents:
USER / FLAT (Initial setting) / POPS / ROCK / NEWS / JAZZ /
ELEC DANCE / HIP HOP / EASY LIS / COUNTRY / CLASSICAL
*2 *1/*3
 LOUDNESS 