Table of Contents
Advertisement
Quick Links
HCD1000RVS, HCD1400RVS, HCD1000NVS, HCD1400NVS,
(See model number confi gurator on page 2 for details.)
Order parts online
www.follettice.com
™
Horizon
for Vision
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Icemaker Installation Instructions
™
Satellite-fi ll
Stock Module Identification Plate
Stock Module Identification Plate
Module No.
Module No.
Product
Product
Service No.
Service No.
™
Applications
remote condensing
208264
208264
00159988R03
Advertisement
Table of Contents
Related Manuals for Follett Horizon HCD1000RVS
Summary of Contents for Follett Horizon HCD1000RVS
- Page 1 ™ Horizon Icemaker Installation Instructions ™ ™ for Vision Satellite-fi ll Applications HCD1000RVS, HCD1400RVS, HCD1000NVS, HCD1400NVS, (See model number confi gurator on page 2 for details.) Order parts online www.follettice.com remote condensing Stock Module Identification Plate Stock Module Identification Plate 208264 208264 Module No.
- Page 2 Horizon Series Icemaker Model Number Configurations 1400 Icemaker Voltage Series Condenser Application Configuration HC Horizon C 208-230/60/1 1000 up to Air-cooled, self-contained V Vision™ S Satellite-fill™ (self-contained only) 1036 lbs Chewblet W Water-cooled, self-contained H Harmony™ T Top-mount D Low side 115/60/1 (471kg) HM Horizon R Air-cooled, remote condensing unit...
- Page 3 Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Louvered docking assembly Ice transport tube External connection Internal connection Front cover VISION • SATELLITE-FILL remote condensing...
- Page 4 Unpack Carefully unpack and inspect the contents of your Follett icemaker. Unpack icemaker ➊ ➋ ➌ ➍ 1/2" 1/2" ➎ ➏ VISION • SATELLITE-FILL remote condensing...
-
Page 5: Site Preparation
Potable water supply • 10-70 psi (69-483kpa) • 45-90 F (7-32 C) • Follett recommends the use of an in-line water filtration system (item# 00130286) ➌ Drain • The drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m) ➍... -
Page 6: Dispenser Preparation
Dispenser preparation Prepare the dispenser. Bin Signal Installation ➏ ➎ ➏ ➋ Ground ➊ 24" (610 mm) ➌ ➌ ➍ ➊ • Mount the electrical box to the side of the Vision dispenser to establish a ground connection. Note: If a 4 x 4 box is mounted to a non-grounded surface, connect ground wire at an appropriate ground. - Page 7 Louvered docking assembly Install the louvered docking assembly. Wall bracket accessory Machine stand accessory • Mount louvered docking assembly to wall • Mount louvered docking assembly to bracket accessory machine stand accessory Louvered docking assembly 1-3/4" (44,5mm) 3" (76mm) ➋ 1"...
- Page 8 Undercounter installation requirements Horizon 1000 & 1400 series Top View ➌ ➊ 1.75" (45mm) min. Access panel/ door on counter 24.5" min. (623mm) 21" min. (534mm No Lip ➋ DOCKING STATION • Position and screw louvered docking assembly to the bottom of counter inside of access ➊...
- Page 9 Transport tube Install the ice transport tube. Dispenser ice transport tube installation Ice tube retainer bracket 1" (25mm) ice tube retaining bracket ➋ ice tube ice tube Front View Front View VU155 VU300 ice tube retaining bracket thermostat thermostat ➋ ice tube ➋...
- Page 10 Ice transport tube installation. ➋ Hot Water 160 F (71 C) ➎ ➍ ➏ ➐ ➊ 1/4" ➌ Ice transport tube tips ➊ • Insulate entire length of ice transport tube ➋ • Secure ice transport tube as needed to prevent dips and traps from forming. For long tube runs see guide on page 15.
-
Page 11: External Connections
External connections Connect utilities to louvered docking assembly. Water and drain Refrigerant ➋ ➊ ➊ • Remove access panel if necessary. • Braze supplied expandable refrigerant ➊ lines in place ➊ • Install drain line The rigid drain line from the icemaker must have at least 1/4"... -
Page 12: Internal Connections
Internal connections Connect louvered docking assembly to icemaker. Ice transport tube installation Water and drain lines ➊ ➋ ➋ ➊ ➋ ➊ • Slide icemaker into louvered docking ➊ • Insert potable water line into valve ➊ assembly • Push drain line over hose barb on •... - Page 13 Power cord • Position plate into opening and secure with supplied screw VISION • SATELLITE-FILL remote condensing...
-
Page 14: Front Cover
Front cover Install front cover to icemaker. Install condensing unit Install icemaker front cover ➋ ➊ • Complete installation of condensing unit • Slide icemaker cover over machine or connection to rack system. ensuring that tabs on back of cover slip under louvers on back of louvered ➊... - Page 15 Long tube run recommendations ➊ max. 2 ft (.6m) ➋ 1/4" ➊ • Pitch ice transport tube to allow melt water to drain towards icemaker ➋ • Secure insulated ice transport tube at least every 2 ft (.6m) to prevent dips or traps VISION •...
- Page 16 801 Church Lane • Easton, PA 18040, USA 00159988R03 Toll free (877) 612-5086 • +1 (610) 252-7301 01/11 www.follettice.com...