Summary of Contents for Follett Horizon HCD1000RHT
Page 1
™ Horizon Ice Machine Installation Instructions ™ for Harmony Top-mount Applications HCD/HMD/HCF/HMF1000RHT, HCD/HMD/HCF/HMF1400RHT, HCD/HMD/HCF/HMF1650RHT, HCD/HMD1000NHT, HCD/HMD1400NHT, HCD/HMD1650NHT (See model number confi gurator on page 2 for details.) Order parts online www.follettice.com remote condensing Horizon top-mount ice machines fi t most countertop dispensers manufactured by Cornelius •...
Page 2
® Chewblet Ice Machine Model Number Configurations 1400 Icemaker Voltage Series Condenser Application Configuration MC Maestro™ C 208-230/60/1 (icemaking head) 400 up to A Air-cooled, self-contained V Vision™ S RIDE™ Self-contained only. 454 lbs ® Chewblet W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 (icemaking head) (206kg)
Page 3
Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Louvered docking assembly Ice transport tube External connection Internal connection Front cover HARMONY • TOP-MOUNT remote condensing...
Page 4
Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine ➊ ➋ ➌ ➍ 1/2" 1/2" ➎ ➏ HARMONY • TOP-MOUNT remote condensing...
Potable water supply • 10-70 psi (69-483kpa) • 45-90 F (7-32 C) • Follett recommends the use of an in-line water fi ltration system (item# 00130286) ➌ Drain • The drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m) ➍...
Dispenser preparation Prepare the dispenser. Note: The instructions below only apply to 22" & 30" wide dispensers. 44" wide dispenser instructions may be found with the top kit. Top preparation – ALL Top preparation – ALL ➊ ➊ ➌ ➊ ➊...
Page 7
Agitation adjust. – CORNELIUS Top preparation – LANCER ➊ ➋ ➋ Lancer models only Cornelius models ED, DB, DF, IDC and ➊ FLAVOR FUSION • Remove protective tape ➋ Adjust the agitation timer located on the • Apply gaskets Cornelius PC board to 1 second on, 1 hour off.
Page 8
Agitation adjustments – LANCER FS SERIES Initialization Screen (Boot Up Only) Lancer FS-16 Ver. 0.200 ➊ Main Menu Sub-Catagory FS-16 Setup Brands Per Side Major/Minor V:1 L:2 R:1 FS-16 Setup Bonus Key Setup Config Bonus Key V:1 T:F M:S B:W FS-16 Setup Soda/Plain Water Cancel...
Page 9
3.10 Dispenser diverter plate installation – CORNELIUS ED, DF and DB SERIES storage bin ➊ gate gate restrictor mounting plate plate ➋ ice diverter (supplied) gasket ice chute flange extends into storage bin through gate opening flat washer apply food-grade silicone sealant 10-32 nut to this surface...
Page 10
3.11 Restrictor plate adjustment – CORNELIUS IDC and FLAVOR FUSION ➋ adjust restrictor plate to fully open position ➊ Cornelius IDC and Flavor Fusion These dispensers require the adjustment of the ice restrictor plate. ➊ • Loosen four nuts on ice chute assembly ➋...
Ice transport tube Install the ice transport tube. Ice transport tube ➋ Hot Water 160 F (71 C) ➊ ➌ • Install supplied ice transport tube installation • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with ➊...
External connections Connect utilities to louvered docking assembly. Water and drain ➋ ➊ • Remove access panel if necessary. ➊ • Install drain line The rigid drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m).
Front cover Install front cover to ice machine. Install condensing unit Install ice machine front cover ➋ ➊ • Complete installation of condensing unit • Slide ice machine cover over machine or connection to rack system. ensuring that tabs on back of cover slip under louvers on back of louvered ➊...
Page 20
Horizon, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett Corporation. Chewblet is a registered trademark of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA 00159970R06 Toll free (877) 612-5086 • +1 (610) 252-7301 3/12 www.follettice.com...