1. Manuals
  2. Brands
  3. GBC Manuals
  4. Laminator
  5. GBC 2064WF-1
  6. Installation and operating manual

GBC 2064WF-1 Installation And Operating Manual

Wide format laminator
Hide thumbs
Table of Contents

Advertisement

Quick Links

GBC 2064WF-1
Operation Manual
GBC 2064WF-1
INSTALLATION & OPERATING MANUAL
Part Number: TBD, Rev A.
GB
Operating Instructions
I
Istruzioni per l'Uso
D
Bedienungsanleitungen
NL
Gebruiksaanwijzing
F
Mode d'Emploi
E
Instrucciones de Operación
Part Number: ???-???
© 2009 General Binding Corporation an ACCO Brands CO.
Page 1

Advertisement

Table of Contents
loading

Related Manuals for GBC GBC 2064WF-1

Summary of Contents for GBC GBC 2064WF-1

  • Page 1: Cover

    GBC 2064WF-1 Operation Manual GBC 2064WF-1 INSTALLATION & OPERATING MANUAL Part Number: TBD, Rev A. Operating Instructions Istruzioni per l'Uso Bedienungsanleitungen Gebruiksaanwijzing Mode d'Emploi Instrucciones de Operación Part Number: ???-??? © 2009 General Binding Corporation an ACCO Brands CO. Page 1...

  • Page 2: Legal Disclaimer

    GBC. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual...

  • Page 3: Table Of Contents

    Main Roller Lift Handle On/Off Switch &Fuses Main Power Cord Foot Switch Pull Roll Clutch IR Sensor © 2009 General Binding Corporation an ACCO Brands CO. Page Description LCD Error Screens Sequence of Operations Operating Instructions Film Loading and Threading...

  • Page 4: Important Safety Instructions

    UNTIL YOU HAVE COMPLETELY READ THESE INSTRUCTIONS. MAINTAIN INSTRUCTIONS IN A CONVENIENT LOCATION FOR FUTURE REFERENCE. © 2009 General Binding Corporation an ACCO Brands CO. IMPORTANT SAFEGUARDS WARNING: TO GUARD AGAINST INJURY THE FOLLOWING SAFETY PRECAUTIONS MUST BE OBSERVED IN INSTALLATION AND USE OF THE LAMINATOR.

  • Page 5: Warranty

    3. Damage caused by lifting, tilting or attempting to position the laminator other than rolling it on its castors across even surfaces. FOR EUROPEAN UNION RESIDENTS ONLY: This guarantee does not affect the legal rights which consumers have under applicable national legislation governing the sale of consumer goods. © 2009 General Binding Corporation an ACCO Brands CO. Page 5...

  • Page 6: Specifications

    Toutes modifications apportées à ce dispositif et non approuvées par General Binding Corporation annuleront le droit accordé à l'utilisateur par le FCC et/ou par Industrie Canada de faire fonctionner cet équipement. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Page 6...

  • Page 7: Pre-Installation

    Lay a level on top of the main and pull rolls. Then, check level from main roll to pull roll on right and left side of the roll. Finally, check by placing the level diagonally across lower main to lower pull rolls. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual...

  • Page 8: Control Panel

    • SPEED: Speed is displayed in Feet per Minute or ft/mn. FIGURE 5 Displays the Speed set at 8ft. © 2009 General Binding Corporation an ACCO Brands CO. • GAP: As the rollers are lifted, the GAP is measured digitally. The value is shown as a percentage.

  • Page 9: Rear Control

    GBC 2064WF-1 REAR CONTROL © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual A. Stop Button: • While running the machine from the Rear, by pressing the “STOP” button, the rollers will stop. B. Rear Button: • By pressing the “Rear” button, the machine will work going to the rear of the machine.

  • Page 10: Features Guide

    FEATURES GUIDE (DETAILED DESCRIPTION) FIGURE 1 FIGURE 2 FIGURE 3 © 2009 General Binding Corporation an ACCO Brands CO. EMERGENCY STOP BUTTONS: (Fig. 1– Item A) Four Emergency Stops buttons are available on the Laminator on the top four corners of the Laminator.

  • Page 11: Rear Media Table

    GBC 2064WF-1 FIGURE 4 FIGURE 5 FIGURE 6 FIGURE 7 © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Rear Media Table: The Rear Media Table (Fig.4A) is used to position items for Lamination. There are two media tables on the machine one on the front &...

  • Page 12: Lower Tension Idler

    GBC 2064WF-1 FIGURE 8 FIGURE 9 FIGURE 10 FIGURE 11 © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Lower Tension Idler: (Fig.8A&9A) Lower Tension Idler: (Fig.8A&9A) The Lower Tension Idler Guides the lower The Lower Tension Idler Guides the lower...

  • Page 13: Nip Pressure Adjustment

    GBC 2064WF-1 FIGURE 12 FIGURE 13 FIGURE 14 © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Nip Pressure Adjustment: Nip Pressure Adjustment: The Nip pressure adjustment allows the operator to The Nip pressure adjustment allows the operator to...

  • Page 14: Main Power Cord

    GBC 2064WF-1 FIGURE 15 FIGURE 16 FIGURE 17 © 2009 General Binding Corporation an ACCO Brands CO. Main Power Cord: (Fig. 15A) The Main Power Cord Plugs into the Main Power Supply. See Power Requirements in the Specs part of the manual for required Voltage and Amperage.

  • Page 15: Lcd Error Screens

    BOT:098*F MODE:FWRD GAP:000% ESW SW PRESSED!!! FIGURE 1. FIGURE 2. FIGURE 3. FIGURE 4. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual FIGURE 1: ESW SW PRESSED!!! -Indicates that an Emergency Stop activated. Locate Emergency Stop and release it. This will return the machine to normal operating condition.

  • Page 16: Sequence Of Operations

    Press Reverse take over from control Push button switch. panel. © 2009 General Binding Corporation an ACCO Brands CO. Situation 2 Situation 3 Interrupted optic beam Optic beam cleared + all safety or opened any safety circuitries are closed circuitry.

  • Page 17: Operating Instructions

    4. Push the film shaft back into the film shaft Support saddle. 5. Push the clevis pin down. 6. Center the roll of film. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Polyester surface Polyester surface FIGURE 17...

  • Page 18: Threading Card

    12. Once the threading card has completely exited the pull rollers, press the stop ( ) button. 13. Now refer section LAMINATING. © 2009 General Binding Corporation an ACCO Brands CO. to On. THERMAL LAMINATE entitled START THERMAL LAMINATE...

  • Page 19: Webbing Psa Film/Mount Adhesive Using Threading Card

    Film CHILLED ROLLER HEAT ROLLER Mount Adhesive FIGURE 24 © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Webbing PSA Film/Mount Adhesive Using Threading Card The laminator should be cool to the touch before Proceeding. 1. Turn the Power ON...

  • Page 20: Start Laminating

    CAUTION: Avoid forcing the image into the main roller nip as this action will cause the corners of the leading edge to buckle and create a wave. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual FIGURE 25 FIGURE 26...

  • Page 21: Method For Tacking New Film To Existing Film

    FIGURE 27 ...a PSA film or mount adhesive FIGURE 28 © 2009 General Binding Corporation an ACCO Brands CO. Method for Tacking New Film to Existing Film The following describes a method for loading film whereby the existing film present on the heat rollers may be used in place of the threading card to draw the new film through the laminator.

  • Page 22: To Unweb The Laminator

    6. Once the film jam has been cleared, lower the main roller and pull rollers. 7. Refer section titled LAMINATING. © 2009 General Binding Corporation an ACCO Brands CO..a PSA film or mount adhesive START Operation Manual FIGURE 28 PULL WEB...

  • Page 23: Applications

    RELEASE LINER FROM PSA FILM IMAGE KRAFT PAPER OPTION FIGURE 32 © 2009 General Binding Corporation an ACCO Brands CO. Tips for Pre Coating Boards MOUNT ADHESIVE 1. Load the laminator as illustrated in (Fig. 30). Remove chill idler. LEADER BOARD 2.

  • Page 24: Tips For Creating A Decal

    6. Length and width of image, ink coverage and paper type may affect the temperature and speed recommended in the SPEED/ TEMPERATURE GUIDE. © 2009 General Binding Corporation an ACCO Brands CO. THERMAL OR PSA FILM RELEASE LINER FROM PSA FILM...

  • Page 25: Accushield

    PAPER OPTION FIGURE 36 FIGURE 37 FIGURE 38 © 2009 General Binding Corporation an ACCO Brands CO. Tips for AccuShield 1. Load the laminator as illustrated in Fig. 36. OPTIONAL 2. You must have the Separator bar option to SEPERATOR BAR accurately run this material.

  • Page 26: Speed/Temperature Control

    Adjustment of the pull roller clutch may be necessary if after adjusting unwind and rewind brake tensions do not improve your output quality. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Page 26...

  • Page 27: Heat

    - A - FIGURE 40 - A - FIGURE 41 © 2009 General Binding Corporation an ACCO Brands CO. Heat The “READY” indicator may extinguish if the speed is set too fast for the material being laminated. Either lower the speed setting or press STOP ( ) and wait until the “READY”...

  • Page 28: Maintenance

    Continue this process until the complete surfaces of both rollers are clean. Refer to the beginning of the section entitled OPERATING INSTRUCTIONS to web your laminator. NOTE: Do not use metal scouring pads to clean the rollers. © 2009 General Binding Corporation an ACCO Brands CO. Operation Manual Page 28...

  • Page 29: Trouble Shooting Guide

    Heat rollers only turn if I use the “Footswitch”. Laminated items exhibit curling. Adhesive deposited on heat rollers. Unsatisfactory adhesion of laminate. © 2009 General Binding Corporation an ACCO Brands CO. POSSIBLE CAUSE Laminator not connected to electrical supply Blown out fuse. Feed table not properly installed.

  • Page 30: Service Agreement

    GBC write to: ACCO Brands Inc. IN CANADA: 300 Tower Parkway Lincolnshire, IL 60069 U.S.A. © 2009 General Binding Corporation an ACCO Brands CO. GBC NATIONAL SERVICE 49 RAILSIDE ROAD DON MILLS, ONTARIO M3A 1B3 Operation Manual Page 30...

Table of Contents