Page 1
ENCORE 1350/3350HR TREADMILL OWNER’S MANUAL Proudly made in the USA by: KEYS Fitness Products, LP P.O. Box 551239 Dallas, Texas 75239 PART# 15-0115...
Table of Contents Information Table of Contents Specification Sheet Important Safety Information Before You Start Warm Up Exercises Assembly Instructions Power Requirements Console Functions and Descriptions Program and Operating Instructions Program Descriptions and Profiles Belt Adjustments and Tension Change to MPH or Km/H Maintenance Instructions Troubleshooting Guide Parts and Diagrams...
Specification Sheet Horsepower (Continuous) Display Type Electronics Pre-Set Programs Semi-Custom Programs User Programs Heart Rate Program Heart Rate Interactive Power Incline Roller Diameter Cushioned Deck Speed Range Walking Belt Side Hand Rails Foot Print Warranty Motor Warranty Parts Warranty Labor Warranty Frame EC1350 EC3350HR...
Never insert any object or body parts into any opening. For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time. Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer.
Do not stand on the walking belt while pressing the Power button or Start/Stop button. Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds. If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate.
Warm Up Exercises EXERCISE GUIDELINES ! Before beginning this or any exercise program, you should consult your physician. This is es- WARNING pecially important for individuals over the age of 35 or individuals with pre-existing health problems. Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and raising body temperature.
4) Tighten all four screws snugly. CAUTION: DO NOT OPERATE TREADMILL WITHOUT SECURING REAR ROLLER HOUSING!!! Be sure the treadmill is level to the floor. The rear feet can be adjusted to level the treadmill. Assembly is now complete! Figure 1 Figure 2...
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
(1-10) and shows position with a blinking action. In Program mode, the treadmill will display the name of the program selected This is shown on the left hand side of the window. In Manual mode, the LAP counter will appear in the top center of the window, counting each 1/4 mile lap in sequence of completion (1, 2, 3, etc.)
To end your workout, press START/STOP button. Belt will gradually slow to zero. To pause your workout, press PAUSE. To re-start after pausing: Press the PAUSE button. WARNING: The treadmill belt will resume at the speed the treadmill was moving before pausing.
Page 11
Program and Operating Instructions PROGRAM MODE-FOR THE EC1350 Plug treadmill into a surge protector outlet . Attach RED Safety Key to treadmill console. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window will flash.
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be entered. The TIME window will flash. The “Heart” shape on the treadmill will be flashing if the Heart Rate Transmitter is transmitting.
Program Profiles The Fat Burn Program is designed to vary treadmill elevation while maintaining a constant walking belt speed. Each program contains 10 segments or intervals. For instance, a 30 minute program will have 10 three-minute segments (30 minutes divided by 10). Also, each preset program may be customized for speed, incline, or both. Please see “Program and Operating Instructions”...
WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1) First, turn treadmill on to run at 1 mph. Using the hex key provided, turn the left rear roller adjustment bolt ¼ turn in the clockwise direction.
1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the console. 2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside of the console (see diagram below).
6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.
(Refer to “Power Requirements”) 3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in.
Parts & Diagrams 15. & 16. 15. & 16. Please review the following drawing below to familiarize yourself with the listed parts. This manual covers several treadmills, so the one pictured below may not be identical to your particular model. 05-0020-Extrusion side board deluxe/left 05-0019-Extrusion side board deluxe/right 04-0012-Belt walk spliced 18 x 113”...
EC1350C/EC3350HR- Parts List PART # DESCRIPTION QTY PART # 02-0004 SCREW-8x5/8 PHIL PH AB BLACK 02-0005 SCREW-8x5/8 PPH HILO BLACK TPB 02-0006 BOLT-HEX 5/16-18x5 1/ GRADE 5-ZP 02-0007 NUT 5/16-18 NYLOCKZP 02-0008 BOLT-CARRIAGE 5/16-18x3/4"GRADE 2-ZP 02-0009 NUT-HEX 5/16 WIZ-FL-LK-ZP 02-0013 WASHER LOCK 1/4"...
Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty. To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts determined to be defective must be returned to Keys to obtain warranty service.