Figure 2 - Husqvarna FS 9900 D Operator's Manual

FIGURE 2

BLADE SHAFT BOLT: Use to clamp the diamond
2A.
2 C 2 C 2 C 2 C
2 B 2 B 2 B 2 B
2 J 2 J 2 J 2 J
2 D 2 D 2 D 2 D
2 A 2 A 2 A 2 A
blade between the inner and outer fl ange. Right
side of saw has left hand threads. Left side of saw
has right hand threads.
OUTER FLANGE: Use to hold the diamond blade
2B.
in position.
OUTER FLANGE ARBOR: Use to support the
2C.
diamond blade.
LOCKING PIN: Use to prevent the diamond blade
2D.
from rotating on the shaft during operation.
DIAMOND BLADE: Use as the cutting tool for
2E.
concrete and asphalt surfaces.
INNER FLANGE: Inside support used to hold the
2F.
diamond blade in position.
BLADE GUARD NOSE LATCH: Use to latch the
2G.
front part of blade guard down.
BLADE GUARD FRONT: The front part of the
2H.
blade guard.
BLADESHAFT: Supports Blade Flanges and blade.
2I.
LOCK WASHER: Prevents Bladeshaft Bolt from
2J.
loosening.
50
2 H 2 H
2 G 2 G
2 I 2 I 2 I 2 I
2 F 2 F 2 F 2 F
2 E 2 E 2 E 2 E
FIGURE 3-1
3-1D
3-1A
3-1B
3-1C
3-1J
3-1E
3-1F
3-1I 3-1H
3-1A. ENGINE GEARBOX: Single Speed Model.
3-1B. WATER CONNECTION: Circulates freshwater
through gearbox to cool it. Water then fl ows to
the bladeguard.
3-1C. WATER DRAIN VALVE: To drain water from gear-
box: Turn Counterclockwise to open, Clockwise to
close. Drain daily to prevent corrosion or damage
due to freezing temperatures.
3-1D. HOOD LATCH: One latch secures hood in lowered
position. US Model Operation: 1. Press HOOD
LATCH (3-1D3/3-2D3) inward. 2. Raise hood
until HOOD SUPPORT (6H) is engaged & sup-
ports hood. CE Model Operation: 1. Use tool to
loosen Capscrew (3-1D1/3-2D1). 2. Pivot tube latch
(3-1D2/3-2D2) downward. 3. Press HOOD LATCH
(3-1D3/3-2D3) inward. 4. Raise hood until HOOD
SUPPORT (6H) is engaged & supports hood.
3-1E. FLANGE COVER: Guards against FLANGE
contact during operation. Always keep in place!
3-1F. BELT PROTECTOR SHIELD: Keep in place.
3-1G. BLADESHAFT TUBE ASSY: Sealed unit contains
bladeshaft, bearings and shaft seals.
3-1H. TIEDOWN LUGS: Used to tie the saw down
while transporting by vehicle. Not to be used to lift
the saw.
3-1I. ENGINE OIL DRAIN VALVE: Drains engine oil
without use of tools.
3-1J. BELT TENSIONING BOLTS:
3-1K. HORIZONTAL CLAMPING BOLTS:
3-1L. BLADE SHAFT PULLEY:
3-1M. V-BELTS: Set of 4.
3-1N. GEARBOX PULLEY:
3-1D3
3-1D2
3-1D1
3-1N
3-1M
3-1G
3-1K
3-1L