Sign in today to find solutions:

Don't have an account? Sign up

Kenwood TK-2302 Instruction Manual

Kenwood vhf/uhf fm transceiver instruction manual.

 
TK-2302/ TK-2302V
TK-3302/ TK-3302U
VHF FM TRANSCEIVER/
UHF FM TRANSCEIVER
INSTRUCTION MANUAL
ÉMETTEUR-RÉCEPTEUR FM VHF/
ÉMETTEUR-RÉCEPTEUR FM UHF
MODE D'EMPLOI
TRANSCEPTOR FM VHF/
TRANSCEPTOR FM UHF
MANUAL DE INSTRUCCIONES
© B62-2139-00 (K, P)
09 08 07 06 05 04 03 02 01 00

Summary of Contents

  • Page 1

    TK-2302/ TK-2302V TK-3302/ TK-3302U VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES © B62-2139-00 (K, P) 09 08 07 06 05 04 03 02 01 00...

  • Page 2

    For information on Li-ion battery recycling in your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Kenwood’s involvement in this program is part of our commitment to preserve our environment and conserve our natural resources. ATTENTION: The RBRC Recycle seal found on Kenwood nickel metal hydride (Ni-MH) battery packs indicates Kenwood’...

  • Page 3

    We are grateful you have chosen Kenwood for your land mobile radio applications. oTices To The ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment.

  • Page 4

    One or more of the following statements may be applicable: FCC WARNING Ths equpment generates or uses rado frequency energy. Changes or modfcatons to ths equpment may cause harmful nterference unless the modfcatons are expressly approved n the nstructon manual. The user could lose the authorty to operate ths equpment f an unauthorzed change or modfcaton s made.

  • Page 5

    Ensure that there are no metallc tems located between the transcever and the battery pack. • Do not use optons not specfed by Kenwood. • If the de-cast chasss or other transcever part s damaged, do not touch the damaged parts.

  • Page 6

    • If an abnormal odor or smoke s detected comng from the transcever, swtch the transcever power off mmedately, remove the battery pack from the transcever, and contact your Kenwood dealer. • Use of the transcever whle you are drvng may be aganst traffc laws.

  • Page 7

    Information concerning the battery pack: The battery pack ncludes flammable objects such as organc solvent. Mshandlng may cause the battery to rupture producng flames or extreme heat, deterorate, or cause other forms of damage to the battery. Please observe the followng prohbtve matters.

  • Page 8

    Use only the specified charger and observe charging • requirements! If the battery s charged n unspecfed condtons (under hgh temperature over the regulated value, excessve hgh voltage or current over regulated value, or wth a remodeled charger), t may overcharge or an abnormal chemcal reacton may occur.

  • Page 9

    • Do not touch a ruptured and leaking battery! If the electrolyte lqud from the battery gets nto your eyes, wash your eyes wth fresh water as soon as possble, wthout rubbng your eyes. Go to the hosptal mmedately. If left untreated, t may cause eye-problems.

  • Page 10

    TK-2302/ TK-3302: KSC-3 • TK-2302V/ TK-3302U: KSC-35 • Battery pack ...  • TK-2302/ TK-3302: KNB-29N (Ni-MH) • TK-2302V/ TK-3302U: KNB-45L (Li-ion) • Speaker/ microphone jack cover ...  • Speaker/ microphone locking bracket ...  • Belt clip (KBH-0) ...  •...

  • Page 11

    nStAlling emoving the Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. ◆ PREPARATION Attery 1 Align the battery pack with the back of the transceiver, then press the battery pack and transceiver firmly together until the release latch on the base of...

  • Page 12

    nStAlling the ntennA Antenna nStAlling the Belt clip Do not use glue which is designed to prevent screw loosening when installing the belt clip, as it may cause damage to the transceiver. Acrylic ester, which is contained in these glues, may crack the transceiver’s back panel.

  • Page 13

    nStAlling the over over the Speaker/ microphone jack cover nStAlling the ptionAl Speaker/ microphone locking bracket peAker If you are not using a speaker/ microphone, install the cover over the speaker/ microphone jacks using the supplied 3 x 6 mm screw. Note: To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied...

  • Page 14

    hArging the Attery ATTENTION: Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into the charger. Charging slot Indicator 4 When charging is completed, the indicator lights green. Remove the battery pack or the transceiver from the charging slot of the charger.

  • Page 15

    Antenna Channel selector Rotate to change the operating channel. • Channel Annunciation: When changing channels, the transceiver will announce the newly selected channel number. (This can be deactivated by your dealer.) LED indicator For the LED indicator status, refer to page 9. Power switch/ Volume control Turn clockwise to switch ON the transceiver.

  • Page 16

    PROGRAMMABLE AUXILIARY FUNCTIONS Your dealer can program the Side 1 and Side 2 keys each with one of the following functions. ■ None No function has been programmed. ■ Autodial DTMF Autodial allows you to make a private call to another party.

  • Page 17

    ■ Scrambler The Scrambler function allows you to hold a conversation in complete privacy. When activated, any other party listening in on your channel will be unable to understand your conversation. ■ Squelch Off Momentarily press this key to hear background noise. Press the key again to return to normal operation.

  • Page 18

    1 Turn the Power switch/ Volume control clockwise to switch the transceiver power ON. • A beep sounds if enabled by your dealer. 2 Press the key programmed with the Monitor or Squelch Off function to hear background noise, then rotate the Power switch/ Volume control to adjust the volume.

  • Page 19

    VOICE OPERATED TRANSMISSION (VOX) VOX operation allows you to transmit hands-free. This feature must first be activated by your dealer, and can only be used if you are using a supported headset. To activate VOX and set the VOX Gain level, perform the following steps: 1 Connect the headset to the transceiver .

  • Page 20

    BACKGROUND OPERATIONS (tot) imer The Time-out Timer prevents callers from using a channel for an extended duration. If you continuously transmit for the duration programmed by your dealer (default is  minute), transmission will stop and an alert tone will sound. To stop the tone, release the PTT switch.

  • Page 21

    The DTMF decode capabilities include Selective Call ID, Transpond with ID, and “Wild Card” Group Calling. ■ FleetSync Utilizing Kenwood’s FleetSync digital signaling protocol, this transceiver has PTT ID and Selective Calling capabilities for managed dispatch operations. eginning...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: