Kenwood TK-2302 Instruction Manual
Vhf fm transceiver/ uhf fm transceiver
Hide thumbs
Also See for TK-2302:
- Instruction manual (21 pages) ,
- Service manual (46 pages) ,
- Instruction manual (132 pages)
Advertisement
Advertisement
Related Manuals for Kenwood TK-2302
Summary of Contents for Kenwood TK-2302
-
Page 1: Instruction Manual
TK-2302/ TK-2302V TK-3302/ TK-3302U VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES © B62-2139-00 (K, P) 09 08 07 06 05 04 03 02 01 00... - Page 2 For information on Li-ion battery recycling in your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Kenwood’s involvement in this program is part of our commitment to preserve our environment and conserve our natural resources. ATTENTION: The RBRC Recycle seal found on Kenwood nickel metal hydride (Ni-MH) battery packs indicates Kenwood’...
- Page 3 We are grateful you have chosen Kenwood for your land mobile radio applications. oTices To The ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment.
- Page 4 One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
- Page 5 Ensure that there are no metallic items located between the transceiver and the battery pack. • Do not use options not specified by Kenwood. • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts.
- Page 6 • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery pack from the transceiver, and contact your Kenwood dealer. • Use of the transceiver while you are driving may be against traffic laws.
- Page 7 Information concerning the battery pack: The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters.
- Page 8 • Use only the specified charger and observe charging requirements! If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodeled charger), it may overcharge or an abnormal chemical reaction may occur.
- Page 9 • Do not touch a ruptured and leaking battery! If the electrolyte liquid from the battery gets into your eyes, wash your eyes with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems.
-
Page 10: Table Of Contents
TK-2302/ TK-3302: KSC-31 • TK-2302V/ TK-3302U: KSC-35 • Battery pack ................1 • TK-2302/ TK-3302: KNB-29N (Ni-MH) • TK-2302V/ TK-3302U: KNB-45L (Li-ion) • Speaker/ microphone jack cover ..........1 • Speaker/ microphone locking bracket ........1 • Belt clip (KBH-10) ..............1 •... -
Page 11: Preparation
PREPARATION NSTALLING EMOVING THE ATTERY ◆ Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. 1 Align the battery pack with the back of the transceiver, then press the battery pack and transceiver firmly together until the release latch on the base of... - Page 12 NSTALLING THE NTENNA Screw the antenna into the connector on the top of the transceiver by Antenna holding the antenna at its base and turning it clockwise until secure. Note: The antenna is neither a handle, a key ring retainer, nor a speaker/ microphone attachment point.
- Page 13 NSTALLING THE OVER OVER THE PEAKER ICROPHONE ACKS If you are not using a speaker/ microphone, install the cover over the speaker/ microphone jacks using the supplied 3 x 6 mm screw. Note: To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cover.
- Page 14 HARGING THE ATTERY ATTENTION: Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into the charger. 1 Plug the AC adapter cable into the jack located on the rear of the charger. 2 Plug the AC adapter into an AC outlet.
-
Page 15: Orientation
ORIENTATION Antenna Battery pack Channel selector Rotate to change the operating channel. • Channel Annunciation: When changing channels, the transceiver will announce the newly selected channel number. (This can be deactivated by your dealer.) LED indicator For the LED indicator status, refer to page 9. Power switch/ Volume control Turn clockwise to switch ON the transceiver. -
Page 16: Programmable Auxiliary Functions
PROGRAMMABLE AUXILIARY FUNCTIONS Your dealer can program the Side 1 and Side 2 keys each with one of the following functions. ■ None No function has been programmed. ■ Autodial DTMF Autodial allows you to make a private call to another party. - Page 17 ■ Scrambler The Scrambler function allows you to hold a conversation in complete privacy. When activated, any other party listening in on your channel will be unable to understand your conversation. ■ Squelch Off Momentarily press this key to hear background noise. Press the key again to return to normal operation.
-
Page 18: Basic Operations
BASIC OPERATIONS 1 Turn the Power switch/ Volume control clockwise to switch the transceiver power ON. • A beep sounds if enabled by your dealer. 2 Press the key programmed with the Monitor or Squelch Off function to hear background noise, then rotate the Power switch/ Volume control to adjust the volume. -
Page 19: Voice Operated Transmission (Vox)
VOICE OPERATED TRANSMISSION (VOX) VOX operation allows you to transmit hands-free. This feature must first be activated by your dealer, and can only be used if you are using a supported headset. To activate VOX and set the VOX Gain level, perform the following steps: 1 Connect the headset to the transceiver . -
Page 20: Background Operations
BACKGROUND OPERATIONS (TOT) IMER The Time-out Timer prevents callers from using a channel for an extended duration. If you continuously transmit for the duration programmed by your dealer (default is 1 minute), transmission will stop and an alert tone will sound. To stop the tone, release the PTT switch. - Page 21 The DTMF decode capabilities include Selective Call ID, Transpond with ID, and “Wild Card” Group Calling. ■ FleetSync Utilizing Kenwood’s FleetSync digital signaling protocol, this transceiver has PTT ID and Selective Calling capabilities for managed dispatch operations. EGINNING...