Page 1
DTR-8.2 3 7 63 1515 0 Ref. No.3713 SERVICE MANUAL SERVICE MANUAL Oct, 2001 AV Amplifier DTR-8.2 Standby/On Master Volume Standby Power O f f Direct/ Zone Pure Audio Rec ( Audio Video 1 Video 2 Video 3 Video 4...
DTR-8.2 3 7 63 1515 0 SERVICE PROCEDURES 1. Replacing the fuses 3. Safety-check out This symbol located near the fuses indicates that the After correcting the original service problem, perform the fuse used is fast operating type. For continued protection against following safety check before releasing the set to the customer.
DTR-8.2 3 7 63 1515 0 PANEL VIEWS FRONT PANEL 1 Standby/On Master Volume Standby Power O f f Direct/ Zone Pure Audio Rec ( Audio Video 1 Video 2 Video 3 Video 4 Video 5 Tape Phono Selector...
Standby/On button (Zone 2). When this button is pressed with the main power switch turned on, the DTR-8.2 turns on and the display lights up. Press again to return Rec Out/Zone 2/Off buttons the DTR-8.2 to the standby state. These buttons allow you to use the DTR-8.2 to output to a remote...
Page 6
DTR-8.2 3 7 63 1515 0 PANEL VIEWS FRONT PANEL 3 Tuning buttons Use these buttons to change the tuner frequency. The tuner frequency is displayed in the front display and it can be changed in 50 kHz increments for FM and 10 kHz increments for AM.
Using auxiliary power amplifiers allows you to listen at louder There are three digital inputs with coaxial jacks and four with optical volumes than with the DTR-8.2 alone. If power amplifiers are used, jacks. The inputs accept digital audio signals from a compact disc, connect each speaker to the corresponding power amplifier.
Page 8
DTR-8.2. By doing this, you can use the Standby/On ZONE 2 AUDIO/VIDEO OUT button on the DTR-8.2 to turn on and off the connected devices as L 13942296513 Connect the device that will be used in the remote zone (Zone 2).
Page 9
IR IN/OUT REAR PANEL 3 If the DTR-8.2 is located inside a rack or cabinet that will not allow infrared beams to reach the IR sensor, you will need to connect a remote sensor to IR IN input to be able to use the remote controller.
L 13942296513 Select an input source. CD: CD, DVD: DVD, Tuner: FM/AM, Phono: PHONO, Tape1: TAPE, Tape2: Not used with the DTR-8.2, Video1: VIDEO 1, Video2:VIDEO 2, Video3:VIDEO 3, Video4:VIDEO 4, Video5: VIDEO 5 Audio Sel button For selecting the audio input signal. The setting changes from “...
Page 11
Sets the sleep function. and DTS Neo:6 Cinema.Neo6:Cinema DTS Neo6:Music. The Sleep button enables you to set the DTR-8.2 to turn off THX: Changes the listening mode to the THX listening mode. automatically after a specified time period. When the THX listening mode is selected SP A/B buttons •...
Page 12
Input Selector buttons Selects an input source. CD: CD, DVD: DVD, Tuner: FM/AM, Phono: PHONO, Tape1: TAPE, Tape2: Not used with the DTR-8.2, Video1: VIDEO 1, Video2: VIDEO 2, Video3: VIDEO 3, Video4: VIDEO 4, Video5: VIDEO 5 L 13942296513 u163 http://www.xiaoyu163.com...
Page 17
DTR-8.2 3 7 63 1515 0 IC BLOCK DIAGRAMS AND DESCRIPTIONS L 13942296513 u163 http://www.xiaoyu163.com...
Page 18
DTR-8.2 3 7 63 1515 0 IC BLOCK GIAGRAMS AND DESCRIPTIONS TC74VHC574FT(Octal D-FF with 3-state output) INPUTS OUTPUT CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q X :Don't care Z :High impedance...
Page 19
DTR-8.2 3 7 63 1515 0 IC BLOCK DIAGRAMS AND DESCRIPTIONS TX-DS787 L 13942296513 u163 – 11 – http://www.xiaoyu163.com...
DTR-8.2 http://www.xiaoyu163.com 3 7 63 1515 0 ADJUSTMENT AND CONFIRMATION PROCEDURES 1 Idling current adjustment Before Idling adjustment, turn the trimming resistors R6040 to R6046 to counter clockwise. Connect the DC voltmeter to sockets P6080 to P6086. After turn POWER to ON, adjust the trimming resistors R6040, R6041 and R6042 so that the reading of voltmeter becomes 7.0 mV.
Page 26
DTR-8.2 3 7 63 1515 0 ADJUSTMENT AND CONFIRMATION PROCEDURES 2 3. Confirmation of Current detection circuit Set the unit to "TEST-1-00". Connect the differentiating circuit and apply the 200Hz square signal to MULTI CHANNEL INPUT terminal. of each channel.
DTR-8.2 http://www.xiaoyu163.com 3 7 63 1515 0 ADJUSTMENT AND CONFIRMATION PROCEDURES 3 Test Mode 1. Turn POWER button on. 2. Press and hold down CD button, then press DISPLAY and STANDBY/ON buttons. 3. After "TEST-1" on the FL tube is displayed, press CD button to set the unit to the test mode of FL tube.
Page 28
DTR-8.2 3 7 63 1515 0 MAIN MICROPROCESSOR-CONNECTION DIAGRAM D 6 6 0 3 F R O N T C H . S U R R O U N D C H . V O L U M E...
Page 29
DTR-8.2 3 7 63 1515 0 MAIN MICROPROCESSOR-CONNECTION DIAGRAM D 6 6 0 3 Q 2 9 1 0 , 1 1 T o B U S 1 2 V R L 6 6 0 3 T R I G G E R...
DTR-8.2 3 7 6 3 1 5 1 5 0 MAIN MICROPROCESSOR Terminal Descriptions No. Function Act. Description Function Act. Description BYTE Input pin to change the width of external data bus. Connect to Vss. ADR152 Signal output pin to control address 15 of flash memory for second DSP.
Page 31
DTR-8.2 3 7 6 3 1 5 1 5 0 SUB MICROPROCESSOR-CONNECTION DIAGRAM P 7 4 8 1 H E A D P H O N E S H P D E T D 7 5 3 4 Q 7 5 3 4...
DTR-8.2 3 7 63 1515 0 SCHEMATIC DIAGRAM 6-1 Power amplifier section 2 N A A F - 7 2 5 0 Q 6 0 3 3 1 . 2 V 5 6 . 5 V R 6 1 6 3...
Page 48
DTR-8.2 3 7 63 1515 0 SCHEMATIC DIAGRAM 6-2 Power amplifier section 2 R 6 2 3 0 R 6 2 7 0 5 6 . 5 V 1 2 0 R 6 0 8 0 1 . 3 V 5 6 .
Page 49
DTR-8.2 3 7 63 1515 0 SCHEMATIC DIAGRAM 7-1 Power supply, Fan control & Speaker terminal sections N A E T C - 7 2 3 6 N A E T C - 7 2 3 7 P 6 8 0 0...
DTR-8.2 3 7 63 1515 0 SCHEMATIC DIAGRAM 8-1 Video section N A V D - 7 2 6 8 2 S C 2 7 1 2 G R T K 1 5 4 2 0 M Q 2 1 0 3...
Page 52
DTR-8.2 3 7 63 1515 0 SCHEMATIC DIAGRAM 8-2 Video section N A V D - 7 2 6 9 R 2 4 0 3 7 5 Q 2 4 0 4 L S 1 Z 2 * < I = V 1 >...
Page 53
DTR-8.2 3 7 63 1515 0 SCHEMATIC DIAGRAM 9-1 Mother section N A A R - 7 2 6 7 T O N A P S - 7 2 5 2 ( S C H . 7 - 2 )
Page 54
DTR-8.2 3 7 6 3 1 5 1 5 0 SCHEMATIC DIAGRAM 9-2 Componet video and RS-232C sections N A V D - 7 2 7 0 N A E T C - 7 2 7 2 R S 2 3 2 , I R I N , R I , 1 2 V T R I G E R...
Page 55
DTR-8.2 3 7 6 3 1 5 1 5 0 SCHEMATIC DIAGRAM 10 A-bus section N A E T C - 7 2 6 5 N J M 4 5 6 5 M - D C 1 5 0 4 2 .
DTR-8.2 http://www.xiaoyu163.com 3 7 63 1515 0 PRINTED CIRCUIT BOARD-PARTS LIST 1 MAIN CIRCUIT PC BOARD (NADG-7226-1C) CIRCUIT NO. PART NO. DESCRIPTION CIRCUIT NO. PART NO. DESCRIPTION Capacitors C7703-C7705 356721019R2 100uF,6,3V,Elect. Q100-Q102 22241448R2 NJM4580M-D C7711 356780109R2 1uF,50V,Elect. Q103 22241522R2 AK4528VF...
Page 57
DTR-8.2 3 7 63 1515 0 PRINTED CIRCUIT BOARD-PARTS LIST 2 NOTE: THE COMPONENTS IDENTIFIED BY MARK ! ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE ONLY WITH PART NUMBER SPECIFIED. PRIMARY CIRCUIT PC BOARD (NAPS-7233-1G) CIRCUIT NO.
Page 58
DTR-8.2 http://www.xiaoyu163.com 3 7 63 1515 0 PRINTED CIRCUIT BOARD-PARTS LIST 3 CAUTION: Replacement for transistor of mark *, if necessary must be made from the same beta group (H ) as the original type. CIRCUIT NO. PART NO. DESCRIPTION CIRCUIT NO.
Page 85
DTR-8.2 3 7 63 1515 0 EXPLODED VIEW Chassis section 2 P7701 Q6062 F9501 F9503 Q6066 F9504 Q6056 F6502 Q6050 Q6063 NOTE: THE COMPONENTS IDENTIFIED BY MARK ! Q6053 ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE ONLY WITH PART NUMBER SPECIFIED.
DTR-8.2 3 7 63 1515 0 EXPLODED VIEW Rear panel section P1010 F901 NOTE: THE COMPONENTS IDENTIFIED BY MARK ! ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE ONLY WITH PART NUMBER SPECIFIED. L 13942296513 REF.NO. PART NO.
DTR-8.2 3 7 63 1515 0 PACKING PROCEDURES Bottom Put a sheet on the door and close a door. Accessary bag P901 L 13942296513 NOTE: THE COMPONENTS IDENTIFIED BY MARK ! ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE ONLY WITH PART NUMBER SPECIFIED.