Check Sw Version; Set Assembly Adjustment Method; Adjustment Of White Balance: (Forautomatic Adjustment); Input Area-Option - LG 42LE5500 Service Manual

4.6. Check SW Version

4.6.1. Method
1) Push In-star key on Adjust remote-controller.
2) SW Version check
IN START
Model Name : Global-Plat
1.Adjust Check
Serial Number : SKJY1107 2.ADC Date
S/W Version : 00.00.06.01 3.Power Off Status
MICOM Version : 2.00.2 4.System
BOOT Version : 1.01.01 5.Model Number D/L
URSA Version : 1.00 6.Test Option
IR LED Version : ff 7.External ADC
EDID Version(RGB) : 0.01 8.Bluetooth Test
EDID Version(HDMI) : 0.02 9.Bluetooth AV CODEC Config
Maker : 99 10.Spread Spectrum
BT S/W Version : 1.21 11.Sync Level
BT H/W Version : 4384 12.Wireless Ready
Wireless Host Version : 0.00.0 13.Stable Count
Wireless B/B Version : 0.00.0
MAC Address : FF:FF:FF:FF:FF:FF
UTT : 9
UI Res. Version : 1.06
APP History Ver. : xxxxx

5. SET assembly adjustment method

5.1. Input Area-Option

5.1.1. Profile : Must be changed the Area option
value because being different of
each Country's Language and

signal Condition.

5.1.2. Equipment : adjustment remote control.
5.1.3. Adjustment method
- The input methods are same as other chassis.(Use IN-
START Key on the Adjust Remocon.)
Refer to Job Expression of each main chassis ass'y
(EBTxxxxxxxx) for Option value.
Copyright LG Electronics. Inc. All right reserved.
Only for training and service purposes
Adjust Check
¢" ¢"
1. Country Group(Press OK to Save)
Country Group Code
11
Country Group
A-CAS
Country
-
2. Tool Option
Tool Option1
16672
Tool Option2
Tool Option3
Tool Option4
Tool Option5
3. Adjust White Balance : OK
4. Adjust ADC : OK
480i Component
OK OK
1080p Component
OK OK
RGB
OK
OK
5.EDID : OK
RGB
OK(0x1C) OK(0x1C)
HDMI1
OK(0xD6,0xF9)
OK(0xD6,0xF9)
HDMI2
OK(0xD6,0xF9) OK(0xD6,0xF9)
HDMI3
OK(0xD6,0xF9) OK(0xD6,0xF9)
HDMI4 OK(0xD6,0xF9)
OK(0xD6,0xF9)
- 11 -
5.2. Adjustment of White Balance : (For
Automatic Adjustment)
A Purpose : Adjust the color temperature to reduce the
deviation of the module color temperature.
A Principle : To adjust the white balance without the
saturation,
Fix the one of R/G/B gain to 192 (default data)
and decrease the others.
A Adjustment mode : Three modes – Cool / Medium / Warm
* Required Equipment
A Remote controller for adjustment
A Color Analyzer : CA100+ or CA-210 or same product
(should be used in the calibrated ch by CS-1000)
• LCD TV : CH-9
• PDP TV : CH-10
• White LED TV : CH-14
• RGB LED(MNT) : CH-16
A Auto W/B adjustment instrument(only for Auto adjustment)
5.2.1. Adjustment of White Balance : (For Automatic
Adjustment)
Connecting diagram of equipment for measuring (For
Automatic Adjustment)
Probe
* If TV internal pattern is used, not needed
1) Set TV in adj. mode using POWER ON key
2) Zero calibrate probe then place it on the center of the
Display
3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre
mode(Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
• W/B Adj. must begin as start command "wb 00 00" , and
finish as end command "wb 00 ff", and Adj. offset if need
* Luminance min value is 150cd in the Cool/Medium/Warm
mode( For LCD)
Co lo r Analyzer
RS -232C
Co m p ut er
RS -232C
RS -232C
Pat t ern Generat o r
Signal Source
LGE Internal Use Only