Table of Contents
Advertisement
Audio Control
Audio setup
Sets up volume offset, dual zone function, etc.
1
Start audio setup
ATT
VOL
AUD
SETUP
Q
MENU
2
Select features to set
ATT
VOL
AUD
SETUP
Q
MENU
Each time the knob is rotated, the type
changes in the following order.
Feature
Setting range
HPF
Specifies the front high-pass filter cutoff
frequency.
HPR
Specifies the rear high-pass filter cutoff
frequency.
LPF
Specifies the low-pass filter cutoff frequency.
PHAS
Specifies the subwoofer phase.
V-OFF
Adjusts the volume difference between sources.
LOUD
Corrects treble and bass when the volume is low.
AVOUT
Specifies the output level of the AV OUT terminal.
2ZON
Turns the dual zone function ON/OFF.
3
Set up each feature
ATT
VOL
AUD
SETUP
Q
MENU
The setting range of each item is as follows:
Features
HPF/HPR
LPF
PHAS
V-OFF
LOUD
AVOUT
2ZON
44
KDV-5234
FM
M/S
AM
STOP
SCAN
RDM
REP
F.SEL
M.RDM
FM
M/S
AM
STOP
SCAN
RDM
REP
F.SEL
M.RDM
FM
M/S
AM
STOP
SCAN
RDM
REP
F.SEL
M.RDM
Setting range
THRU (Filter Off)/40/60/80/100/120/150/
180/220 (Hz)
50/60/80/100/120 (Hz)/THRU (Filter Off)
REV (180˚)/NML (0˚)
-8 – 0
OFF/ON
-15 – 0
OFF/DVD/AUX
4
Exit audio setup
ATT
VOL
AUD
SETUP
TI
SCRL
AME
/PTY
DISP
SW
SRC
• If a volume offset is set for each source with "V-OFF", the
volume will be nearly the same for all sources when the
source is changed.
• When "2ZON" is ON ("DVD"/"AUX"), you can only set "V-
OFF" and "LOUD".
TI
SCRL
AME
• If the dual zone function is used, different sources can be
output from the front speakers (source of this unit) and
/PTY
DISP
SW
the rear speakers (disc source of this unit or the sound
SRC
input to the built-in AUX).
• For "LPF" and "PHAS", the feature "SWPRE" needs to be
set to "SW" (subwoofer) in advance in the menu setup,
and the subwoofer output to ON. For details on how to
set up "SWPRE", refer to <Menu setup> (page 50), and for
subwoofer output, refer to <Subwoofer output control>
(page 45).
• "PHAS" cannot be set up when "LPF" is set to "THRU".
• "AVOUT" can be set when the feature "SWPRE" in <Menu
setup> (page 50) is set to "AV".
Speaker setup
Fine adjust the System Q value to the speakers.
1
Set to STANDBY mode
VOL
TI
SCRL
AME
AUD
SETUP
/PTY
DISP
SW
SRC
STANDBY
Select "STANDBY".
2
Set to the speaker matching mode
ATT
VOL
AUD
SETUP
M/S
Q
MENU
STOP
SCAN
RDM
REP
F.SEL
M.RDM
M/S
Q
MENU
STOP
SCAN
RDM
REP
F.SEL
M.RDM
M/S
Q
MENU
STOP
SCAN
RDM
REP
F.SEL
M.RDM
TI
FM
SCRL
AME
/PTY
DISP
AM
SW
SRC
/PTY
DISP
AM
SW
SRC
OFF
TI
FM
SCRL
AME
/PTY
DISP
AM
SW
SRC
Advertisement
Table of Contents
