System Setup; Display Driver - Panasonic Toughbook CF-37 Series Supplementary Instructions Manual

11 Read the entire [Windows NT Licensing Agreement] (use
to scroll down) and press F8 .
12 A list of hardware and software will be displayed. Con-
firm the contents and press Enter .
13 Select [Unpartitioned space] (the largest size), then press
C .
Input [4095] at the [Create partition of size], press Enter .
Select [C:New (Unformatted) 4095MB] , press Enter .
14 Select [Format the partition using the NTFS file sys-
tem], then press Enter .
Formatting will begin automatically.
15 Without changing the location (\WINNT) of the instal-
Enter
lation, press .
16 Press Enter to start the examination of your hard
disk. The copying of files will begin automatically.
17 If the message [This portion of Setup has completed success-
fully.] is displayed, do not remove the CD-ROM. Press
Enter .
18 Windows will restart. When [Press <F2> to enter Setup]
is displayed, press F2 and run the Setup Utility. If the
Setup Utility is unable to be run, turn the power off after the
[Welcome to Setup] is displayed, and perform step 18 again.
19 Press F9 . At the confirmation message, select [Yes]
and press Enter .
20 Press F10 . At the confirmation message, select [Yes]
and press Enter . Windows will restart several times.
21 At the [Windows NT Setup], select [Next].
22 At the [Setup Options], select [Typical] then select [Next].
23 Input your name and organization then select [Next].
(It is possible to omit the organization item.)
24 Input the Product Number written on the "Certificate
of Authenticity" located in the Windows NT Book that
comes with this computer then select [Next].
To move the cursor to a particular item, press
click the desired box.
25 Input your computer name then select [Next].
26 Input an Administrator password then select [Next].
CAUTION
Remember this password! If the password is forgot-
ten, Windows NT cannot be operated.
27 At the [Emergency Repair Disk], select [No, do not create an
emergency repair disk.], then select [Next].
28 At the [Windows NT Components], select [Install the most
common components (recommended)], then select [Next].
29 At the [Windows NT Setup], select [Next].
30 Select [Do not connect this computer to a network at
this time] and select [Next], then select [Finish].
31 At the [Date/Time Properties], set the correct settings
then select [Close]. (Default: GMT)
32 At the [Detected Display], select [OK].
33 At the [Display Properties], select [OK].
34 If the message [Windows NT 4.00 has been installed suc-
cessfully.] is displayed, remove the CD, then press
Enter
35 At the [Begin Logon], press Ctrl + Alt + Del .
Input the password set in step 26 and select [OK], then
select [Close] at the [Welcome]. (This step has to be per-
formed each time the computer is started up.)

System setup

36 Set the Firstaid CD into the CD-ROM drive and select
[Start] - [Programs] - [Command Prompt]. Input the fol-
lowing at the MS-DOS prompt (C:\>).
d: Enter
install.bat Enter
37 Input the following and then close [Command Prompt].
exit Enter
<When one or more Backup Disks have been created>
Shut down the computer, then replace the CD-ROM
drive with a SuperDisk drive. For each disk starting from
the second disk, (in the order given) set the disk into the
SuperDisk drive and select [Start] - [Programs] - [Com-
mand Prompt]. Input the following.
Input the following and then close [Command Prompt].
Shut down the computer, then replace the SuperDisk
drive with a CD-ROM drive.
Power on. (Perform step

Display driver

or
38 Select [Change] for [Adapter Type] in [Start] - [Settings] -
[Control Panel] - [Display] - [Settings] - [Display Type].
39 Select [Have Disk] at the [Change Display], input
[c:\util\drivers\video], then press [OK].
40 Select [Silicon Motion Lynx Family], then select [OK].
41 Select [Yes] at the [Third-party Drivers]. At the [Install-
ing Driver], select [OK].
42 Select [Close] at the [Display Type], then select [Close]
at the [Display Properties].
If the display asks you to restart Windows, select [Yes].
35 after Windows restarts.)
(Perform step
43 At the [Invalid Display Settings], select [OK].
44 At the [Display Properties], set [65536 Colors] for the
[Color Palette], set [800 by 600 pixels] for the [Desktop
Area], select [Test] then select [OK].
45 If there are no problems with the testing mode, select [Yes]
then select [OK] at the [Display Properties].
a: Enter
install.bat Enter
exit Enter
35 .)
9