Page 1
RP 330 Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Pressing Tool Visit us at www.TestEquipmentDepot.com WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire and/or serious personal injury.
Pressing A Fitting With Typical Actuator and Press Ring Set ..................8 Inspecting The Pressed Connection ..........................9 Maintenance Instructions Cleaning and Lubrication ............................10 Required Maintenance at RIDGID Authorized Service Center ................10 Accessories ................................10 Storage ..................................10 Service and Repair ..............................10 Troubleshooting ................................11 RP 330 Diagnostic Codes ............................12...
RP 330 Pressing Tool RP 330-B Battery Tool RP 330-C Corded Tool RP 330 Pressing Tool Record Serial Number below and retain product serial number which is located on nameplate. Serial Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com...
RP 330 Pressing Tool Safety Symbols In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safe- ty information. This section is provided to improve understanding of these signal words and symbols. This is the safety alert symbol.
RP 330 Pressing Tool Personal Safety • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the pow- • Stay alert, watch what you are doing and use com- er tool or these instructions to operate the power mon sense when operating a power tool.
Pressing Tool Safety • Charge batteries in temperatures above +41°F • Use the RP 330 Pressing Tool only with RIDGID (+5°C) and below +113°F (45°C). Store tool and Standard pressing attachments (jaw set, press battery pack in locations where temperatures will ring, actuator, etc.).
RP 330 Pressing Tool NOTE! RIDGID jaw sets are offered in two “series” cate problems such as improper temperature, open jaw mounting pin or maintenance required. • Standard Series • Compact Series Attachment These jaw sets are not interchangeable. That is,...
Using an incorrect attachment for an application can cause injury, damage the tool and make incomplete connections. For a complete listing of RIDGID attach- Figure 3 – Label On Bottom Of Battery ments available for this tool. Make sure that the tool and attachment have been inspected as directed 6.
2. Connect RP 330 to proper power source. For the the previously identified clear path, and with dry hands RP 330-B, insert fully charged battery into the base of plug the pressing tool in. Keep all connections dry the handle. For the RP 330-C plug the tool into an and off the ground.
1. Make sure the RP 330 Pressing Tool has the correct actuator installed. 2. Connect RP 330 to proper power source. For the RP 330-B, insert fully charged battery into the base of the handle. For the RP 330-C plug the tool into an appropriate outlet.
NOTE! If yellow LED service indicator blinks, the tool double check the insertion marks made on the should be sent to a RIDGID Authorized Service tube to see that they are still aligned with the end of Center for required maintenance. The tool will not run if it is not maintained within 2,000 cycles the fitting.
RIDGID Standard Pressing tools. Only use attach- ments that are specifically designed to press the fit- ting system you are installing. For a complete listing of RIDGID attachments available for this tool, see the Ridge Tool Catalog. RP 330 Press Tool Accessories...
RP 330 Pressing Tool Troubleshooting SYMPTOM POSSIBLE REASONS SOLUTION Electric cord damaged. Inspect the cord and replace if necessary. Tool will not turn ON when ON/OFF button on Battery is completely discharged or battery has Insert fully charged battery/recharge dead battery display panel is pressed.
RP 330 Pressing Tool RP 330 Diagnostic Codes Status Description Green Glows Tool ON. Blinks Out of acceptable voltage range — Cordless Tools: Replace battery with a fully charged battery. — Corded Tools: Connect tool to a reliable voltage supply. If using extension cord, use 16 AWG for 50' or less, 14 AWG for 50' to 100'.